Hinowa LightLift 15.70 3S Скачать руководство пользователя страница 22

Страница: 22 / 137

4.1.3 TRACKS AUTOMATIC SPEED CONTROL

LL15.70 is equipped with an automatic system to reduce tracks speed or even

stop them in case of stability risk.

This control depends on the following factors:

Weight in the basket

Jib closed or not

Tracks widened or not

Inclination gradients on axles X and Y

On reaching stability limits the system acts as follow:

Tracks speed reduction

Remote control buzzer activated

Tracks movement stopped, display icon



NOTE: To get out from a stability risk condition when tracks movements are

stopped it’s necessary to

press button 8

on remote control as indicated by

the above icon, tracks movements will be allowed in turtle speed for 10 seconds
while the counter-down will be activate on the display. Operator will have to

drive machine back into safe condition.

SPEED CONTROL CONDITIONS ON X AXLE

ALWAYS

X>6°

TURTLE

TRACKS NOT

OPENED

X>8°

BEEPER

X>10°

STOP

+ ALARM ICON

TRACKS OPENED

X>10°

BEEPER

X>13°

STOP

+ ALARM ICON

Содержание LightLift 15.70 3S










































































































































Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды

Hinowa LightLift 15.70 3S, Техническое руководство

Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды