Hinowa LightLift 15.70 3S Скачать руководство пользователя страница 18

Страница: 18 / 137

GROUND PART MOVEMENTS

4.1

TRACKS MOVEMENTS

To allow tracks movements none of the outriggers have

to be touching the ground, doesn’t matter if completely

lifted up or just lifted, doesn’t matter if opened or in

stowed position.

When machine is not closed and aligned, if operator try to
move an outrigger display will remind that machine need

to be closed and aligned by the error message aside.

The operator has to act on the two external remote control red joysticks to
move the tracks.

With the jib closed, i

t’s possible to drive the tracks

standing on the ground or

standing on the basket.

To drive the tracks with jib opened the basket must be taken off its support
and operator will keep remote control in his hand.

NOTE: With Skyguard installed, to unload the basket it has to be
disconnected the Skyguard connector.

While none of the outriggers is touching the ground and basket is taken off its

support on the display is visualized the “JIB ONLY” icon.

“JIB ONLY”

ICON

ERROR

Содержание LightLift 15.70 3S










































































































































Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды

Hinowa LightLift 15.70 3S, Техническое руководство

Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды