HIMA HIMax X-MIO 6 01 страница 36 Скачать руководство пользователя | Manualshive

Страница: 36 / 72

background image

4 Start-up

X-MIO 7/6 01

Page 36 of 72

HI 801 305 E Rev. 5.00

4.2

Mounting and Removing the Module

When replacing an existing module or mounting a new one, follow the instructions given in this
chapter.

When removing the module, the connector board remains in the HIMax base plate. This saves
additional wiring effort since all field terminals are connected via the connector board of the
module.

4.2.1

Mounting a Connector Board

Tools and utilities



Screwdriver, cross PH 1 or slotted 0.8 x 4.0 mm



Matching connector board

To install the connector board

1. Insert the connector board into the guiding rail with the groove facing upwards (see following

figure). Fit the groove into the guiding rail pin.

2. Place the connector board on the cable shield rail.
3. Secure the captive screws to the base plate. First screw in the lower screws than the upper

ones.

To remove the connector board

1.  Release the captive screws from the base plate.
2.  Carefully lift the lower section of the connector board from the cable shield rail.
3.  Remove the connector board from the guiding rail.

Figure 10: Example of how to Insert the Mono Connector Board

«
...
34
35
36
37
38
...
»

Содержание HIMax X-MIO 6 01









































































Отзывы:

Нет отзывов

Похожие инструкции для HIMax X-MIO 6 01

Бренд: Handicare Страницы: 56

Бренд: Fanimation Страницы: 2

Бренд: M2M Страницы: 24

VARIVENT D Series

Бренд: GEA Страницы: 78

Бренд: GEA Страницы: 96

Бренд: GEA Страницы: 66

Бренд: UNI Страницы: 21

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: UNICORECOMM Страницы: 32

Бренд: UNICORECOMM Страницы: 7

Бренд: UNICORECOMM Страницы: 26

Бренд: UNICORECOMM Страницы: 25

Бренд: GEA Страницы: 47

653 - AE Series

Бренд: VAT Страницы: 103

Бренд: Nice Страницы: 32

Бренд: Quantum Страницы: 20

Бренд: Samson Страницы: 36

Бренд: Variotech Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды