Hilti PSA 80, Оригинальная инструкция по эксплуатации

Страница: 18 / 288

12 English
Cleaning and drying the tool
▶
Clean the tool with a clean, soft cloth. If necessary, moisten the cloth slightly with pure alcohol or a little
water.
▶ Do not use any liquids other than pure alcohol or water as these may damage the plastic components.
2.2 Use and care of battery-powered tools
▶
Use only the Hilti batteries specified for use with this product.
▶ Observe the special guidelines applicable to the transport, storage and use of Li-ion batteries.
▶ Check that the product is switched off before fitting the battery.
▶
Do not expose batteries to high temperatures, direct sunlight or fire.
▶
Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 75°C
(167°F).
▶
Do not attempt to charge or continue to use damaged batteries.
▶
If the battery is too hot to touch it may be defective. In this case, place the tool in a non-flammable
location, well away from flammable materials, where it can be kept under observation and allowed to
cool down. Contact Hilti Service after the battery has cooled down.
3 Description
3.1 Accessories 1
@
Battery PSA 81
;
AC adapter PUA 81
=
Battery PSA 82
%
Charger PSA 85
&
Battery PSA 83
(
PUA 82 motor vehicle power adapter
)
Charger PUA 85 19V
+
Battery PSA 80
§
PUA 86 19V motor vehicle power adapter
3.2 Intended use
Use the PSA 80 only to power the Hilti PS 200 S Ferroscan and the PS 200 M monitor. Charge the PSA 80
battery with the PUA 80 charger.
Use the PSA 81 battery only to power the Hilti PS 1000 X-Scans. Charge the PSA 81 (01 and 02) battery
only with the PUA 81 AC adapter or the PUA 82 motor vehicle power adapter. Charge the PSA 81 (05) with
the PUA 85 19V charger or the PUA 81 AC adapter.
Use the PSA 82 battery to power the Hilti PSA 100 monitor. Charge the battery in the device using the
PUA 81 AC adapter or the PUA 82 motor vehicle power adapter. Alternatively, you can use the PSA 85
charger to charge the PSA 82 battery when it is not in the device.
Use the PSA 83 battery to power the Hilti PSA 200 tablet. Use the PUA 85 19V charger to charge the battery
while it is installed in the device.
Use the PSA 85 charger to charge the PSA 82 battery.
Use the PUA 80 charger to charge the PSA 80 battery.
Use the PUA 81 AC adapter to charge the PSA 81 (01, 02 and 05) battery, the PSA 82 battery when it is in
the PSA 100 monitor (when switched off or in operating mode) and the PRA 84 battery.
Use the PUA 82 motor vehicle power adapter to charge the PSA 81 (01, 02 and 05) battery, the PSA 82
battery when it is in the PSA 100 monitor (when switched off or in operating mode) and the PRA 84 battery.
Use the PUA 85 19V charger to charge the PSA 81 (05) battery and to charge the PSA 83 battery in the
PSA 200 tablet.
Use the PUA 86 19V motor vehicle power adapter to charge the PSA 81 battery (05) and to charge the
PSA 83 battery in the PSA 200 tablet.
3.3 Foreseeable faults
Do not use the PUA 85 19V to charge the PSA 81 battery (01 and 02).
Do not use the battery as a power source for other unspecified appliances.
Do not use the device where there is a risk of fire or explosion.
Printed: 28.10.2016 | Doc-Nr: PUB / 5070487 / 000 / 02