Hilti PD 42, Руководство по эксплуатации, Страница: 17 / 181

m
1669.783
5.489
m
m 12.349
24.634
3
m
m 4.347
MAX 8.642 m
m
m
MIN 5.123
3.519
6. The C-button can be pressed at any time to stop
the measuring operation. Each measurement can
then be cleared, one after the other, and measuring
restarted.
NOTE If the C-button is pressed several times or the
FNC-button is pressed, the function will be canceled
or, respectively, restarted.
NOTE If the second distance is measured using
continuous measuring mode (tracking), the result of
the area calculation is updated continuously. This
allows parts of the area to be included/excluded.
NOTE After calculation of an area, the “Plus” button
can be pressed to add another area or, respectively,
the “Minus” button used to subtract an area.
7.6 Measuring volumes
Each step of the volume measurement operation is indic-
ated graphically in the display. For example, to determine
the volume of a room, proceed as follows:
1. Press the FNC-button to activate the volume func-
tion. A volume can be determined in a single meas-
uring operation.
NOTE When the volume function is activated, the
laser beam is already switched on.
2. Aim the range meter at the target.
3. Press the “Measure” button.
The width of the room is measured and the value
displayed.
4. The graphic display automatically prompts you to
measure the length of the room.
5. Aim the tool at the next target to obtain the length
of the room.
6. Press the “Measure” button.
The length of the room is measured and the value
displayed.
7. Press the “Measure” button.
8. Aim the tool at the next target to obtain the height
of the room.
9. Press the “Measure” button.
The volume is calculated and shown in the result
line in the display as soon as the height of the room
has been measured.
All three distances used for the volume calculation
are shown in the intermediate result lines and can be
noted down conveniently at the end of the operation.
10. The C-button can be pressed at any time to stop
the measuring operation. Each measurement can
then be cleared, one after the other, and measuring
restarted.
NOTE If the C-button is pressed several times or the
FNC-button is pressed, the function will be canceled
or, respectively, restarted.
NOTE If the third distance is measured using con-
tinuous measuring mode (tracking), the result of the
volume calculation is updated continuously. This
allows parts of the volume to be included/excluded.
NOTE After calculation of a volume, the “Plus” but-
ton can be pressed to add another volume or, re-
spectively, the “Minus” button used to subtract a
volume.
7.7 Measuring using the “Min/max” function
The “Maximum” function is used mainly to determine
the length of diagonals, while the “Minimum” function
is used to check parallels and set up objects parallel
to each other, or to take measurements in situations
where access is difficult. The “Maximum” function makes
use of continuous measuring mode. The value shown in
the display is updated whenever the measured distance
increases. The “Minimum” function also makes use of
continuous measuring mode. The value shown in the
display is updated whenever the measured distance de-
creases. By combining the “Maximum” and “Minimum”
functions, differences in distance can be determined very
quickly, easily and reliably. The distance between a pipe
and ceiling, or the distance between two objects even
in inaccessible locations, can thus be easily and reliably
determined.
1. Press the FNC-button to activate the “Min/max”
function.
NOTE When the “Min/max” function is activated,
the laser beam is already switched on.
2. Aim the range meter at the target.
3. Press the “Measure” button.
Continuous measuring then begins.
The values shown in the MIN and MAX display areas
are then updated whenever the measured distance
increases or decreases.
en
13
Printed: 08.07.2013 | Doc-Nr: PUB / 5070024 / 000 / 01