Hilti AG 500-11S Скачать руководство пользователя страница 26

Страница: 26 / 34

22 English

The optional

Kwik lock

nut can be used instead of the standard

clamping nut. Grinding discs can then be changed without the need for

additional tools.

1. Disconnect the mains plug from the power outlet.

2. Clean the clamping flange and the quick-release clamping nut.

3. Fit the clamping flange onto the drive spindle.

4. Fit the grinding disc.

5. Screw on the

Kwik lock

nut until it is seated against the grinding disc.

➥ The name

Kwik lock

should be visible when the nut is screwed on.

6. Press the spindle lockbutton and hold it in this position.

7. Turn the grinding disc firmly by hand in a clockwise direction until

the

Kwik lock

nut is tightened securely and then release the spindle

lockbutton.

6.4.4 Removing a grinding disc secured with a Kwik lock nut

1. Disconnect the mains plug from the power outlet.

CAUTION

Risk of breakage and irreparable damage.

If the spindle lockbutton is

pressed while the spindle is rotating, the accessory tool can detach from the

power tool.

▶

Press the spindle lockbutton only when the spindle has stopped rotating.

2. Press the spindle lockbutton and hold it in this position.

3. Release the

Kwik lock

nut by turning it counterclockwise by hand.

4. If the

Kwik lock

nut cannot be released by turning it by hand, use a pin

wrench to turn the nut in a counterclockwise direction.

Never use a pipe wrench! A pipe wrench could damage the

Kwik lock

nut.

5. Release the spindle lockbutton and remove the grinding disc.

Printed: 19.10.2018 | Doc-Nr: PUB / 5402264 / 000 / 01

Содержание AG 500-11S



































Результаты поиска

Содержание AG 500-11S

Отзывы:

Бренды по названию

Популярные бренды

Hilti AG 500-11S, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание AG 500-11S

Отзывы:

Бренды по названию

Популярные бренды