hilscher COMX 100CA-DN Скачать руководство пользователя | Manualshive

Страница: 39 / 78

background image

Design-In - Electrical Aspects

39/78

COMX Communication Modules | Design Guide
DOC100901DG18EN | Revision 18 | English | 2013-12 | Released | Public

© Hilscher, 2002-2013

3 Design-In - Electrical Aspects

3.1 Host Interface

Attention!

All COMX modules have an operation voltage of 3.3 V which reduces the power con-

sumption. Therefore the voltage levels of the signals have to be not higher than 3.3 V
otherwise the module will be damaged.

The next sections show an overview of the signal pinning of the system connector.

3.1.1

Host Interface Overview: Dual-Port Memory Sizes and Modes

The following table lists the dual-port memory size and the supported dual-port memory modes for
the different COMX Modules.

Module

Fieldbus / Protocol

Dual-port Memory
Size

Parallel
Mode

Serial
Mode

COMX 10

COMX 10CA-COS

CANopen Slave

8 KByte

yes

yes

COMX 10CN-COS

CANopen Slave

yes

yes

COMX 10CA-CCS

CC-Link Slave

yes

yes

COMX 10CN-CCS

CC-Link Slave

yes

yes

COMX 10CA-DPS

PROFIBUS DP Slave

yes

yes

COMX 10CN-DPS

PROFIBUS DP Slave

yes

yes

COMX 10CA-DNS

DeviceNet Slave

yes

yes

COMX 10CN-DNS

DeviceNet Slave

yes

yes

COMX 50

COMX 50CA-CCS

CC-Link Slave

16 KByte

yes

-

COMX 50CA-REFO

PROFINET IO Device

yes

-

COMX 100

COMX 100CA-CO

CANopen Master or Slave

16 KByte

yes

-

COMX 100CN-CO

CANopen Master or Slave

yes

-

COMX 100CA-DN

DeviceNet Master or Slave

yes

-

COMX 100CN-DN

DeviceNet Master or Slave

yes

-

COMX 100CA-DP

PROFIBUS DP Master or Slave

yes

-

COMX 100CN-DP

PROFIBUS DP Master or Slave

yes

-

COMX 100CA-RE

Realtime Ethernet Master or Slave

yes

-

COMX 100CN-RE

Realtime Ethernet Master or Slave

yes

-

COMX 51

COMX 51CA-RE

Realtime Ethernet Slave

16 KByte

yes

yes

Table 18: Dual-port Memory Size and supported Modes of the comX Modules

In general, the COMX module supports 14 address lines and thus a dual-port memory size of
16 KB.
In case of the COMX 10 modules even only the lowest 8 KB of the available address space are
supported by the firmware. So not all address lines need to be used. Unused address lines may be
equipped with a pull-down resistor of 560

Ω

.

«
...
37
38
39
40
41
...
»

Содержание COMX 100CA-DN















































































Отзывы:

Нет отзывов

Похожие инструкции для COMX 100CA-DN

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 146

Бренд: Mackie Страницы: 4

Бренд: Lawler Страницы: 5

Бренд: Panasonic Страницы: 8

Бренд: Absima Страницы: 5

Бренд: nvent Страницы: 6

Бренд: Smart Vision Страницы: 5

Бренд: Teledyne Страницы: 47

Бренд: Western Co Страницы: 14

Бренд: Olsen Страницы: 4

Бренд: Hach Страницы: 504

Бренд: Mosa Страницы: 28

Бренд: Jeckson Electric Страницы: 2

Бренд: D+H Страницы: 2

Бренд: GRAUPNER Страницы: 180

Level-Trac LT-310

Бренд: QTS Страницы: 12

RC Electronic DPSI LCD

Бренд: Emcotec Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды