Hillyard 108538 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 117

background image

When the operation is performed, verify that height and incli-
nation adjustment bubble levels of the squeegee are in central
position.

At further confirmation, check that the trailing spring of the
squeegee support has a stroke equal to 100 mm.

Check functionally the resulting adjustment.

6.7.2

Squeegee Actuator

Adjust the micro switches inside the actuator using the appro-
priate adjusting screws.

Requirements:

Switched Off machine, squeegee mounted on the

machine.

Procedure:

Remove the black plastic cover from the brush deck actua-
tor.

Adjust the brush deck lowering micro (brown wire) so that
the squeegee lifting lever does not impact on the actuator
lever.

Do not adjust the brush deck lifting micro (blue wire).

6.8

Disassembly

6.8.1

Squeegee Support

Put the machine in safe conditions.
Disconnect the vacuum hose.
Unscrew the knobs that secure the squeegee to its support and remove the squeegee.
Remove the screw that secures the center head of the squeegee to the frame. To properly remove this screw,

89

«
...
87
88
89
90
91
...
»

Содержание 108538






















































































































Отзывы:

Нет отзывов

Похожие инструкции для 108538

Hakomatic B 1050

Бренд: HAKO Страницы: 80

Бренд: TRILETY Страницы: 22

Бренд: FIORENTINI Страницы: 34

Бренд: Viper Страницы: 31

Бренд: Krüger Technology Страницы: 38

Бренд: Wascomat Страницы: 32

Бренд: Kruger Страницы: 40

TASKI Swingo 150B

Бренд: Sealed Air Страницы: 18

Бренд: Skymsen Страницы: 8

Бренд: XPower Страницы: 16

CT40 ECS MICRO SCRUB

Бренд: IPC Gansow Страницы: 2

Бренд: IPC Soteco Страницы: 10

Бренд: Avani Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды