Hill-Rom FE5000 Скачать руководство пользователя страница 78

Страница: 78 / 108

4.5 Castor
Chapter 4: Removal, Replacement, and Adjustment Procedures

Page 4 - 16

Electrically Operated General Ward Bed

Operation and Maintenance Manual

(154588 REV 1)

2. Hold the new castor (oriented as it will be installed) and use a 11 mm hex

key (or a short piece of 11 mm hex bar) and put the brake pedal in the brake
position (see figure 4-18 on page 4-16).

Figure 4-18. Castor Orientation

3. Check the brake function of the castor by rotating the castor wheel. Use the

hex key to shift the mechanism back to the neutral position. If the castor
did not brake, proceed to step 12, otherwise proceed to step 14.

4. Put the castor in the neutral position.

5. Hold the castor and maintain the orientation and use the hex key to rotate

the castor stem 180 degrees (see figure 4-19 on page 4-16).

Figure 4-19. Castor Position

6. Repeat steps 10 and 11.

7. Install the new castor in the base.

8. Install, but do not tighten the two mount bolts.

Содержание FE5000













































































































Результаты поиска

Содержание FE5000

Отзывы:

Hill-Rom FE5000, Руководство по эксплуатации и обслуживанию, Страница: 78 / 108

Результаты поиска

Содержание FE5000

Отзывы: