Hill-Rom DuraStar Series Скачать руководство пользователя страница 54

Страница: 54 / 165

2.8 Push Handle Malfunction

Chapter 2: Troubleshooting Procedures

DuraStar™ Series Stretcher Service Manual (man268)

Page 2 - 21

2.8

Push Handle Malfunction

1. Another part of the stretcher keeps the push handle from locking into

position.

Yes

↓

→

Go to step 4.

2. Take appropriate actions to eliminate the interference.

This solves the problem.

Yes

↓

→

Go to step 4.

3. Go to “Final Actions” on page 2-8.

4. The push handle falls into position when the release handle is activated.

Yes

↓

→

Replace the push handle latch (refer to procedure 7.7). If this
solves the problem, go to “Final Actions” on page 2-8.
Otherwise, go to step 5.

5. The push handle locks into position.

Yes

↓

→

Replace the push handles (refer to procedure 7.7). If this solves
the problem, go to “Final Actions” on page 2-8. Otherwise, call
Hill-Rom Technical Support at (800) 445-3720.

6. Go to “Final Actions” on page 2-8.

Содержание DuraStar Series






































































































































































Результаты поиска

Содержание DuraStar Series

Отзывы:

Hill-Rom DuraStar Series, Руководство по обслуживанию, Страница: 54 / 165

Результаты поиска

Содержание DuraStar Series

Отзывы: