Hill-Rom DuraStar Series Скачать руководство пользователя страница 52

Страница: 52 / 165

2.6 Siderail Malfunction

Chapter 2: Troubleshooting Procedures

DuraStar™ Series Stretcher Service Manual (man268)

Page 2 - 19

4. Raise the siderail. The siderail latch (A) falls into the locked position (see

figure 2-5 on page 2-19).

Yes

↓

→

Replace the latch (refer to procedure 4.2). If this solves the
problem, go to “Final Actions” on page 2-8. Otherwise, go to
step 8.

Figure 2-5. Siderail Latch

5. Another part of the stretcher interferes with the siderail.

Yes

↓

→

Call Hill-Rom Technical Support at (800) 445-3720.

6. Take appropriate actions to eliminate the interference.

This solves the problem.

Yes

↓

→

Call Hill-Rom Technical Support at (800) 445-3720.

7. Go to “Final Actions” on page 2-8.

m268_015

Содержание DuraStar Series






































































































































































Результаты поиска

Содержание DuraStar Series

Отзывы:

Hill-Rom DuraStar Series, Руководство по обслуживанию, Страница: 52 / 165

Результаты поиска

Содержание DuraStar Series

Отзывы: