Hill-Rom CarePorter P3000 Скачать руководство пользователя страница 207

Страница: 207 / 220

7.3 Vent Display Mount, Siemens™—P300302

Chapter 7: Accessories

Page 7 - 8

CarePorter™ Cart Service Manual (man239)

7.3

Vent Display Mount, Siemens™—P300302

Tools required:

None

Installation

1. Remove the ventilator mount from the shipping container.

2. Set the brake/steer casters to the brake position.

WARNING:

Ensure the bracket weldment is fully seated into the ISS socket before
using the ventilator mount. Failure to do so could result in personal
injury or equipment damage.

3. Insert the bracket weldment (A) into the one of the available ISS sockets

(B) located on either side of the vertical columns (C) (see figure 7-3 on
page 7-8).

Figure 7-3. Ventilator Display Mount Installation

m239_064

Содержание CarePorter P3000





























































































































































































































Результаты поиска

Содержание CarePorter P3000

Отзывы:

Бренды по названию

Популярные бренды

Hill-Rom CarePorter P3000, Руководство по обслуживанию

Результаты поиска

Содержание CarePorter P3000

Отзывы:

Бренды по названию

Популярные бренды