Hill-Rom CarePorter P3000 Скачать руководство пользователя страница 101

Страница: 101 / 220

4.12 Gas Spring

Chapter 4: Removal, Replacement, and Adjustment Procedures

Page 4 - 38

CarePorter™ Cart Service Manual (man239)

Figure 4-14. Gas Spring Assembly

6. Remove the gas spring assembly (B) from the base weldment (D).

Replacement

1. Insert the ball stud (C) into one end of the new gas spring assembly (B),

and apply pressure to the gas spring assembly (B) until the ball stud (C)
snaps into the clip (A).

2. Repeat step 1 to install the other end of the gas spring assembly (B) onto

the ball stud (C) located on the base weldment.

3. Ensure both ends of the gas spring assembly (B) are attached properly to

the ball studs (C).

4. Test the gas spring assembly for proper operation.

Adjustment

No adjustment is required for the gas spring assembly (B).

m239_044

Содержание CarePorter P3000





























































































































































































































Результаты поиска

Содержание CarePorter P3000

Отзывы:

Бренды по названию

Популярные бренды

Hill-Rom CarePorter P3000, Руководство по обслуживанию

Результаты поиска

Содержание CarePorter P3000

Отзывы:

Бренды по названию

Популярные бренды