Hill-Rom 305 Manual Bed Скачать руководство пользователя страница 33

Страница: 33 / 176

2.5 The Knee Up Function Does Not Operate

Chapter 2: Troubleshooting Procedures

Hill-Rom® Basic Care™ Bed, Hill-Rom® 305 Manual Bed,

Page 2 - 11

Hill-Rom® 405 Electric Bed Service Manual (MAN336 REV 2)

2.5

The Knee Up Function Does Not Operate

1. The knee up function does not operate when the knee up switch is pressed

from either the left siderail or the right siderail or from the foot end control
panel.

Yes

↓

→

Go to step 6.

2. The knee function lockout is off.

NOTE:

If the LED for a bed function lockout is on, the function is locked out.

Yes

↓

→

Turn the knee function lockout off. If this corrects the problem,
go to “Final Actions” on page 2-4.

3. Tightly seat the connector for the knee motor into its socket on the control

box. The knee up function does not operate.

Yes

↓

→

Go to “Final Actions” on page 2-4.

4. Replace the knee motor (refer to procedure 4.10 on page 4-23). The knee

up function does not operate.

Yes

↓

→

Go to “Final Actions” on page 2-4.

5. Call Hill-Rom Technical Support at 800-445-3720 (USA).

6. The knee up function operates from the foot end control panel.

Yes

↓

→

Replace the foot end control panel (refer to procedure 4.2 on
page 4-5). If this corrects the problem, go to “Final Actions” on
page 2-4. Otherwise, call

Hill-Rom Technical Support at 800-445-3720 (USA).

7. The knee up function only operates from one of the siderails.

Yes

↓

→

Tightly seat both of the siderail connectors into their sockets on
the control box. If this corrects the problem, go to “Final
Actions” on page 2-4. Otherwise, call Hill-Rom Technical
Support at 800-445-3720 (USA).

Содержание 305 Manual Bed

















































































































































































Результаты поиска

Содержание 305 Manual Bed

Отзывы:

Hill-Rom 305 Manual Bed, Руководство по обслуживанию, Страница: 33 / 176

Результаты поиска

Содержание 305 Manual Bed

Отзывы: