background image

Face Recognition Terminal

     Quick Start Guide

UDB

Ground

Bottom Cover

Bracket

Bottom Screw

M6×65 Expension Bolt

1

2

3

Before you start: 

Make sure the ground surface has drilled 

holes for device installation.

Steps:

1. Remove the two bottom screws (2-SC-KM3×5B-JMF) on 

both sides of the bottom cover. And remove the bottom 

cover.

2. Align the device with the drilled holes on the ground and 

insert 3 supplied expension bolts (M6×65). Make sure the 

expension bolts are higher than the ground.

3. Secure the expension bolts with nuts。

4. Install the bottom cover back on the device with 2 bottom 

screws.

The actual device 

appearance varies 

according to 

different models.

The device should be installed on the concrete surface or other 

non-flammable surfaces.

The device supports plug & play. You can put the device on the 

ground and start operation after powering on.

2

Installation

The figures are for reference only.

   The Wiegand terminal here is a Wiegand input terminal. You should set 

    the device’s Wiegand direction to “Input”. If you should connect to 

    an access controller, you should set the Wiegand direction to “Output”. 

    For details, see the user manual.

   The power supply should be 12 VDC/3 A, 36 W.

IN2

Yellow/Orange

Yellow/Blue

Yellow/Purple

Purple

Grey

Orange

Brown

White

Green

Yellow/Brown

Power

Yellow/Red

(NC)

(NO)

Yellow/Black

Alarm Input Device

Alarm Output Device

Alarm Output Device

A3

A1

A2

A4

A5

A6

B1

B2

B3

B4
B5
B6

WG_OK

WG_ERR

BUZZER

12 V

Power Supply

Wiegand

Car
d R

ead

er

Wiegand

Alarm Input

Alarm Output

Tag 2

Tag 4

Tag 2

Tag 4

RS-48

5

Net
w

ork Int

er

face

Debugging P

or

t

(For Debuggin Only)

Door Lock Int

er

face

Wiegand

Alar
m Input

/Out

put

Pow
er Input

USB Int

er

face 2

USB Int

er

face 1

Device

The wiring diagram of tag 2 and 4 on the left is shown below:

© 2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved.

This Manual is the property of Hangzhou Hikvision Digital Technology Co., Ltd. or its 

affiliates (hereinafter referred to as “Hikvision”), and it cannot be reproduced, changed, 

translated, or distributed, partially or wholly, by any means, without the prior written 

permission of Hikvision. Unless otherwise expressly stated herein, Hikvision does not 

make any warranties, guarantees or representations, express or implied, regarding to the 

Manual, any information contained herein.

About this Manual 

The Manual includes instructions for using and managing the Product. Pictures, charts, 

images and all other information hereinafter are for description and explanation only. The 

information contained in the Manual is subject to change, without notice, due to firmware 

updates or other reasons. Please find the latest version of this Manual at the Hikvision 

website (https://www.hikvision.com/). 

Please use this Manual with the guidance and assistance of professionals trained in 

supporting the Product. 

Trademarks Acknowledgement

                    and other Hikvision’s trademarks and logos are the properties of Hikvision in 

various jurisdictions. 

Other trademarks and logos mentioned are the properties of their respective owners. 

LEGAL DISCLAIMER

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE 

PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED 

“AS IS” AND “WITH ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES, 

EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTO

-

RY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU 

IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, 

CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, 

DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, 

CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH 

OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN 

CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF 

THE POSSIBILITY OF SUCH DAMAGES OR LOSS. 

YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY 

RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL 

OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, 

HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, 

HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. 

YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND 

YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE 

APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A 

MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING 

WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA 

PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY 

PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS 

OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR 

BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR 

EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS 

ABUSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, 

THE LATER PREVAILS. 

Data Protection

During the use of device, personal data will be collected, stored and processed. To protect 

data, the development of Hikvision devices incorporates privacy by design principles. For 

example, for device with facial recognition features, biometrics data is stored in your 

device with encryption method; for fingerprint device, only fingerprint template will be 

saved, which is impossible to reconstruct a fingerprint image. 

As data controller, you are advised to collect, store, process and transfer data in 

accordance with the applicable data protection laws and regulations, including without 

limitation, conducting security controls to safeguard personal data, such as, implementing 

reasonable administrative and physical security controls, conduct periodic reviews and 

assessments of the effectiveness of your security controls.

Scan the QR code to get the user manual for detailed information. 

Note that mobile data charges may apply if Wi-Fi is unavailable. 

Use only power supplies listed in the user instructions:

Model

Manufacturer

Standard

C2000IC12.0-24P-DE
C2000IC12.0-24P-GB

MOSO Power Supply Technology Co., Ltd. CEE
MOSO Power Supply Technology Co., Ltd. BS

ADS-24S-12 1224GPG Shenzhen Honor Electronic Co., Ltd.

CEE

Installation Environment: 

If installing the device indoors, the device should be at least 2 meters 

away from the light, and at least 3 meters away from the window or the 

door. 

Make sure the environment illumination is more than 100 Lux.

Direct Sunlight

Direct Sunlight

through Window

Indirect Sunlight

through Window

Backlight

10Lux

>1200Lux

100~850Lux

3m

2m

Close to Light

1

Appearance

3.1

Device Wiring (Without Secure Door Control Unit) 

165 mm

13

98

.9

5 mm

172 mm

250.71 mm

46 mm

144.71 mm

37 mm

185.91 mm

13

47

.2

8 mm

Touch Screen

IR Light

IR Light
Camera

White Light

Thermal Module

69.96 mm

Отзывы: