Fingerprint Access Control Terminal
Quick Start Guide
UD17820B
1
2
3
Activation
Mounting Screw
Appearance
Installation
1. Install 120 or 86gang box into the wall.
2. Route the cables through the cable hole of
the mounting plate.
3. Secure the device mounting plate on the gang
box with two screws. (Supplied).
4. Connect the corresponding cables.
5. Align the terminal with mounting plate. Push the
terminal in the mounting plate from bottom up.
Fasten the terminal with the buckles on the plate.
6. Tighten the screws to fix the terminal on the
mounting plate and complete the installation.
The default values of the terminal are as follows:
• The default IP address: 192.0.0.64
• The default port No.: 8000
• The default user name: admin
Activating via SADP
1. Download SADP Software
:
Get the SADP software from the supplied disk or the official website. Install and run the software.
2. Activate Device: Check the inactive device from the device list. Create a password in the right side of the interface and confirm the password.
3. Edit Device IP Address: Check the device and manually edit the device IP address, Port No., Subnet Mask, Gateway, etc.
Activating via Client Software
STRONG PASSWORD RECOMMENDED
We highly recommend you create a strong password of your own choosing
(using a minimum of 8 characters, including upper case letters, lower case
letters, numbers, and special characters) in order to increase the security of
your product. And we recommend you reset your password regularly,
especially in the high security system, resetting the password monthly or
weekly can better protect your product.
Activating via Device
Power on and wire the network cable after installation.
You should activate the device before the first login.
After powering on, the interface will be displayed as
follows.
You can create the device password and confirm the
password to activate.
Online Devices (2)
Add to Client
IP
xxxxxxxxxxxxx
xxxxxxxxxxxxx
XX-XXXXXX
8000
Activate
Device Type
Firmware Version
Server Port
Security
Device Serial No.
Add All
Modify Netinfo
Reset Password
Activate
Filter
Refresh Every 60s
xx.xx.xx.xx
xxxxxxxxxxxxx
xxxxxxxxxxxxx
XX-XXXXXX
8000
Inactivate
xx.xx.xx.xx
2.4-inch LCD Display
Screen Indicator
Keypad
Fingerprint
Reading Module
Door Bell
Button
12V
Power Interface
USB Interface/
Reset Button
(Inside of the Cover)
Ethernet Port
Door Lock
Wiring Terminal
Alarm
Wiring Terminal
RS-485/Wiegand Wiring Terminal
Tamper-proof
Button
ESC
OK
1
2
ABC
3
DEF
4
GHI
6
MN
O
7
P
QRS
8
TUV
9
W
XYZ
0
5
JKL
Exiting Key
Direction Keys
Numeric Keys/
Letter Keys
OK Key
Editing Key
Deleting
Key
EN
OK Key:
Press to confirm operations. Press and hold the
key for 3s to login the main interface.
Deleting Key:
1.Press to delete the letters or numbers one by one;
2.Long-press to clear all contents in the textbox;
Numeric Keys/Letter Keys:
Input numbers or letters.
Exiting Key:
Press the button to exit the menu.
Direction Keys:
Use , , and
to move the cursor.
Editing Key:
Press to enter the editing status. Shift among
numbers/lowercases, numbers/uppercases and symbols.
Note:
Long press Key 6 for 3s to enter One-Touch Wi-Fi Settings mode. You can set Wi-Fi parameters
for the device via the App on the phone. Press Key 6 again to exit the mode. (The model with “-1”
does not support One-Touch Wi-Fi Settings mode.)
Keypad Descriptions
Anticlockwise Rotation
©2019 Hangzhou Hikvision Digital Technology Co., Ltd.
It includes instructions on how to use the Product. The software
embodied in the Product is governed by the user license agreement
covering that Product.
About this Manual
This Manual is subject to domestic and international copyright
protection. Hangzhou Hikvision Digital Technology Co., Ltd.
(“Hikvision”) reserves all rights to this manual. This manual cannot
be reproduced, changed, translated, or distributed, partially or
wholly, by any means, without the prior written permission of
Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision
and are registered trademarks or the subject of applications for the
same by Hikvision and/or its affiliates. Other trademarks mentioned
in this manual are the properties of their respective owners. No right
of license is given to use such trademarks without express
permission.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE
PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND
FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,
AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTO
-
RY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-IN
-
FRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS
DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU
FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR
DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS
PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILI
-
TY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF
PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL
NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION,
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER
ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL
RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS
PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE
APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT
THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE
APPLICABLE LAW, THE LATER PREVAILS.
1. Get the client software from the supplied disk or the official website. Install and run the client software.
2. Click Device Management to enter the Device Management interface.
3. Select an inactive device from the Online Device list. Click Activate to pop up the Activation interface.
4. Create a password and confirm the new password. Click OK to activate the device.
4. Click “Modify Netinfo” to set the device IP address, mask address, gateway address, and port No.
