HIKVISION DS-K3Y501 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 47

background image

• Refers to Components Introduction to view the lithium battery's position.

• The working temperature of the lithium battery is 0 °C to 45 °C.

1. Remove the screws on the battery component to disassemble the battery component.

2. Put the lithium battery inside the component.

3. Secure the components on the device by the screws.

4. Insert the battery connecter to the battery interface on the lane control board.

Note

There are battery interfaces on both of the master lane control board and slave lane control

board.

Figure 3-2 Lithium Battery Interface

3.3 Install Pedestals

Before You Start

Prepare for the installation tools, check the device and the accessories, and clear the installation

base.
Steps

Note

• The device should be installed on the concrete surface or other non-flammable surfaces.

• The dimension is as follows.

DS-K3Y501 Flap Barrier Quick Start Guide

20

«
...
29
30
31
32
33
...
»

Содержание DS-K3Y501
















































Отзывы:

Нет отзывов

Похожие инструкции для DS-K3Y501

Бренд: ABB Страницы: 86

Бренд: Obdstar Страницы: 10

Бренд: Raytech Страницы: 21

Бренд: Teac Страницы: 2

Бренд: laerdal Страницы: 2

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

Бренд: h/p/cosmos Страницы: 81

Бренд: Jaga Страницы: 32

Бренд: Parker Страницы: 64

Бренд: Parker Страницы: 40

Matrx Digital MDM

Бренд: Parker Страницы: 20

Бренд: Parker Страницы: 52

Бренд: UNI-T Страницы: 4

UPO3000E Series

Бренд: UNI-T Страницы: 94

Бренд: UMS Страницы: 92

Бренд: ValueStore US Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды