Activation
Activating via Device
Power on and wire the network cable after installation.
You should activate the device before the first login.
If the device is not activated yet, it will enter the Activate Device page
after powering on.
1. Create a password and confirm the password.
2. Tap
Activate
to activate the device.
Note:
For other activation methods, see the device user manual.
1. Tap the settings icon at the lower right corner of the initial
page and input the activation password to enter the main page.
2. Enter the User Management page, tap + to enter the Add User
page.
4. Tap
Face
and collect the face information according to the
instructions.
You can view the captured picture at the upper right corner of
the page. Make sure the face picture is in good quality and size.
For details about the tips and positions when collecting or
comparing the face picture, see the contents on the right.
5. If the picture is in good condition, tap
Save
to save the picture.
Or tap
Try Again
to take another face picture.
6. Tap to save the settings.
Go back to the initial page to start authentication.
For other authentication methods, see the device user manual.
Adding Face Information
Positions When Collecting/
Comparing Face Picture
(Recommended Distance: 0.5m)
Tips When Collecting/
Comparing Face Picture
Expression
Posture
Size
1.4m
0.5m
1.4m
Too High
Too Low
Too Close
Too Far
1.4m
0.5m
1.4m
Make sure your face is in the middle of the collecting window.
Correct
Tilt
Raise
Side
Bow
0.5m
0.5m
激活设备
Activate Device
Password
Confirm
8 to 16 characters
Passwords should be the same
Activate
Recommended Height:
1.43m to 1.90m
Correct
Too Close
Too Far
1.4m
Too
Close
Too
Far
Correct
0.5m
Height:
1.43m to 1.90m
Move
Back and Forth
Note: Two or more of the following characters
are allowed: digit, number, and symbol.
Note:
The device will not support the fingerprint collection
function if the device model contains F.
Recommended:
Use 1:1 Face Matching when the face is hard to recognize.
Use other authentication methods if the device if affected by the light
or other items.
1:1 Matching:
The device will compare the captured face picture with
the ones in the database.
1:N Matching:
The device will compare the captured face picture with
the input employee ID linked face picture.
Notes:
If you require a higher security level, do not use single authentication.
If you adopt multiple authentications mode, you should authenticate
other methods before authenticating face.
This product and
,
if applicable
,
the supplied accessories too are
marked with
“
CE
”
and comply therefore with the applicable
harmonized European standards listed under the RE Directive
2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive
2011/65/EU.
2006/66/EC (battery directive): This product contains a battery
that cannot be disposed of as unsorted municipal waste in the
European Union. See the product documentation for specific
battery information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb),
or mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more
information see:
www.recyclethis.info
2012/19/EU (WEEE directive): Products marked with this
symbol cannot be disposed of as unsorted municipal waste in
the European Union. For proper recycling, return this product to
your local supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collection points. For
more information see:
www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé
pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et
son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse
pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
This equipment should be installed and operated with a minimum distance 20cm
between the radiator and your body.
Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le
radiateur et votre corps.
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
EU Conformity Statement
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC
C
ompliance:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses
,
and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
-
Reorient or relocate the receiving antenna
-
Increase the separation between the equipment and receiver
-
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
-
Consult the dealer or an experienced radio/TV technician for help
This equipment should be installed and operated with a minimum distance
of
20
cm
between the radiator and your body.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
Device Wiring (With Secure Door Control Unit)
In order to get a good quality and accurate face picture, position your
face looking at the camera when collecting or comparing face pictures.
Keep your expression natural when collecting or comparing face
pictures, just like the expression in the picture on the right.
Do not wear
a
hat, sunglasses, or other accessories
that can affect the facial recognition function.
Do not
have
your hair cover your eyes, ears, etc.
and heavy makeup is not allowed.
STRONG PASSWORD RECOMMENDED
–
We highly recommend
that
you create a strong password of your own
choosing (using a minimum of
eight
characters, including upper case letters, lower
case letters, numbers, and special characters) in order to increase the security of your
product.
W
e
also
recommend
that
you reset your password regularly
. E
specially in
a
high security system, resetting the password monthly or weekly can better protect
your product.
Secure Door Control Unit
Wiring Terminal
Note:
The secure door control unit should connect to an external power supply sep
a
rately.
Exit Button
Power Input
SENSOR
BUTTON
B1
B2
B3
B4
Green/Brown
Black
Green/Black
Black
Lock Output
NC
C1
C2
C3
COM
NC
White/Purple
White/Black
White/Red
Red
Black
Door Magnetic
Exit Button
NO
Power
Electric Dropbolt
Electric Strike
Sensor Input
Face Recognition Terminal
4
2.2
3
Scan the QR code to get the user manual
for detailed inform
a
tion.
Note that mobile data charges may apply
if Wi-Fi is unavailable.
Use only power supplies listed in the user instructions:
Model
Manufacturer
Standard
C2000IC12.0-24P-DE
C2000IC12.0-24P-GB
MOSO Power Supply Technology Co., Ltd. CEE
MOSO Power Supply Technology Co., Ltd. BS
ADS-24S-12 1224GPG Shenzhen Honor Electronic Co., Ltd.
CEE
NO
