HIKOKI UB18DB, Инструкция по эксплуатации

Страница: 8 / 136

8
English
CAUTION
○ If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used, the
pilot lamp of the charger lights for 1 second, does not
light for 0.5 seconds (o ff for 0.5 seconds). In such a case,
fi rst let the battery cool, then start charging.
○ When the pilot lamp fl ickers (at 0.2-second intervals),
check for and take out any foreign objects in the charger’s
battery connector. If there are no foreign objects, it is
probable that the battery or charger is malfunctioning.
Take it to your authorized Service Center.
○ Since the built-in micro computer takes about 3 seconds
to con fi rm that the battery being charged with charger
is taken out, wait for a minimum of 3 seconds before
reinserting it to continue charging. If the battery is
reinserted within 3 seconds, the battery may not be
properly charged.
MOUNTING AND OPERATION
Action Figure Page
Inserting the battery 2-a 2
Removing the battery 2-b 2
Charging 3 3
Turning the work light on*
1
4 3
Changing the angle of the work light 5 3
Hanging the work light for use* 2 6 3
Securing to a tripod*
3
7 3
Remaining battery indicator*
4
8 3
Selecting accessories ― 127
*1 When the brightness reaches the maximum (2000 lm) or
the minimum (350 lm), the light brie fl y blinks twice.
*2
NOTE
When using the work light while it is hung by a hook,
hang it from a stable and sturdy object.
*3
NOTE
When using a tripod, ensure that it is stable so that it
does not fall over.
*4
State of lamp Battery Remaining Power
Over 80%
60%–80%
40%–60%
20%–40%
Less than 20%
When the remaining battery becomes low, the light brie fl y
blinks about once every 3 minutes.
As the remaining battery indicator shows somewhat
di ff erently depending on ambient temperature and battery
characteristics, read it as a reference.
NOTE
○ When using a Multi-volt battery, please refer to the
indicator lamp on the battery for the battery remaining
power.
○ Do not give a strong shock to the panel or break it. It may
lead to a trouble.
MAINTENANCE AND INSPECTION
WARNING
When not using the work light for a long time, performing
maintenance on it, inspecting it, or storing it, be sure to
turn OFF the switch and pull out the battery.
1. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
2. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
3. Cleaning on the outside
When the cordless work light is stained, wipe with a soft
dry cloth or a cloth moistened with soapy water.
Do not use chloric solvents, gasoline or paint thinner, for
they melt plastics.
4. Storage
Store the cordless work light and the battery in a place in
which the temperature is less than 40°C and out of reach
of children.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
signi fi cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, signi fi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to fi ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
Important notice on the batteries for the HiKOKI
cordless tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless tool when used with
batteries other than these designated by us, or when
the battery is disassembled and modi fi ed (such as
disassembly and replacement of cells or other internal
parts).
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with
statutory/country speci fi c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling instruction,
to a HiKOKI Authorized Service Center.
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci fi cations herein are subject to
change without prior notice.
00Book̲UB18DB.indb 8 00Book̲UB18DB.indb 8 2021/10/19 11:20:54 2021/10/19 11:20:54