HIKOKI G13SP Скачать руководство пользователя страница 7

English

7

6.  To prolong the life of the machine and ensure a 

fi

 rst 

class 

fi

 nish, it is important that the machine should not 

be overloaded by applying too much pressure. In most 

applications, the weight of the machine alone is su

  cient 

for e

 ective grinding. Too much pressure will result in 

reduced rotational speed, inferior surface 

fi

 nish,  and 

overloading which could reduce the life of the machine.

7.  The wheel continues to rotate after the tool is switched 

o

 .

 

After switching o

  the machine, do not put it down until the 

depressed center wheel has come to a complete stop. 

Apart from avoiding serious accidents, this precaution 

will reduce the amount of dust and swarf sucked into the 

machine.

8.  When the machine is not use, the power source should 

be disconnected.

9.  Be sure to switch OFF and disconnect the attachment 

plug from the receptacle to avoid a serious accident 

before the depressed center wheel is assembling and 

disassembling.

10. RCD

 

The use of a residual current device with a rated residual 

current of 30 mA or less at all times is recommended.

SPECIFICATIONS

Voltage (by areas)*

(110 V, 220 V, 230 V) 

Power Input*

860 W*

No-load speed

9500 /min

Max. Peripheral Speed

80 m/s (4800 m/min)

Wheel size

Outer dia.

125 mm

Thickness

6 mm

Hole dia.

22.23 mm

Weigth (only main body)

2.1 kg

* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) Wrench ......................................................................... 1

(2) Side Handle .................................................................. 1

Standard accessories are subject to change without notice.

APPLICATIONS

  Removal of casting 

fi

 n and 

fi

 nishing of various types of 

steel, bronze and aluminum materials and castings.

  Grinding of welded sections or sections cut by means of 

a cutting torch.

  Grinding of brick, marble, etc.

   Cutting and scribing of concrete, stone, tile, (use the 

diamond wheel)

PRIOR TO OPERATION

1. Power source

 

 Ensure that the power source to be utilized conforms to the 

power requirements speci

fi

 ed on the product nameplate.

2. Power switch

 

 Ensure that the power switch is in the OFF position. If the 

plug is connected to a receptacle while the power switch 

is in the ON position, the power tool will start operating 

immediately, which could cause a serious accident.

3. Extension cord

 

When the work area is removed from the power source, 

use an extension cord of su

  cient thickness and rated 

capacity. The extension cord should be kept as short as 

practicable.

4. Con

fi

 rming condition of the environment

 Con

fi

 rm that the work site is placed under appropriate 

conditions conforming to prescribed precautions.

   When grinding a thin steel plate, depending upon the 

state of the workbench, a loud noise will be created due 

to resounding noise from the steel plate being ground. To 

eliminate unwanted noise in this instance, place a rubber 

mat beneath the material to be ground.

5.  Mounting the wheel guard 

 

The wheel guard is a protective device to prevent injury 

should the depressed center wheel be shattered during 

operation. Ensure that the wheel guard is properly 

fi

 tted 

and fastened before commencing grinding operation. 

 

By slightly loosening the setting screw, the wheel guard 

can be turned and set at any desired angle for maximum 

operational e

 ectiveness. Ensure that the setting screw 

is thoroughtly tightended after adjusting the wheel guard.

6. Con

fi

 rming and mounting the depressed center 

wheel.

   Thoroughly check that a speci

fi

 ed depressed center 

wheel is free of cracks and splits is mounted.

  

Con

fi

 rm that the depressed center wheel is mounted 

under the speci

fi

 ed condition and is 

fi

 rmly clamped.

 

  For details, refer to the item “Assembling and 

Disassembling the depressed center wheel.”

7.  Apply a trial run

   To start grinding work without checking for possible 

cracks and splits in the depressed center wheel is very 

dangerous. Prior to start of grinding, direct the grinder 

in a direction where no one is present, and apply a trial 

run without fail to con

fi

 rm that the grinder displays no 

abnormalities.

  

 Duration of the trial run is as follows:

 

When depressed center wheels is replaced

 

 ............................................... 3 minutes or more

 

When starting daily work ................1 minute or more

8. Con

fi

 rm the spindle lock mochanism. 

 Con

fi

 rm that the spindle lock is disengaged by pushing 

the push button two or three times before switching the 

power tool on (See 

Fig. 2

)

9.  Fixing the side handle.

 

Screw the side handle into the gear cover.

000Book̲G13SP̲Asia.indb   7

000Book̲G13SP̲Asia.indb   7

2021/03/01   10:06:04

2021/03/01   10:06:04

Содержание G13SP

















Отзывы: