HIKOKI FGP 10DL Скачать руководство пользователя страница 41

English

41

MAINTENANCE AND INSPECTION

1.  Inspecting the accessories

 

Using a tip tool or mandrel with a worn or damaged end will not only result in a poor 

fi

 nish, but 

will place unreasonable strain on the motor, causing reduced e

  ciency, damage or injury.

 

If the tip tool or mandrel is worn or damaged, replace it.

2.  Inspecting the mounting screws

 

Regularly inspect all mounting screws and ensure that they are properly tightened. Should 

any of the screws be loose, retighten them immediately. Failure to do so could result in 

serious hazard.

3.  Maintenance of the motor

 

The motor unit winding is the very “heart” of the power tool.

 

Exercise due care to ensure the winding does not become damaged and/or wet with oil or 

water.

4.  Cleaning of the outside

 

When the grinder is stained, wipe with a soft dry cloth or a cloth moistened with soapy 

water. Do not use chloric solvents, gasoline or paint thinner, for they melt plastics.

5. Storage

 

Store the grinder in a place in which the temperature is less than 40°C and out of reach of 

children.

NOTE

 

Storing Lithium-ion Batteries

 

Make sure the batteries have been fully charged before storing them.

 

Prolonged storage (3 months or more) of batteries with a low charge may result in 

performance deterioration, signi

fi

 cantly reducing battery usage time or rendering the 

batteries incapable of holding a charge.

 However, 

signi

fi

 cantly reduced battery usage time may be recovered by repeatedly 

charging and using the batteries two to 

fi

 ve times.

 

If the battery usage time is extremely short despite repeated charging and use, consider 

the batteries dead and purchase new batteries.

6.  Service parts list

CAUTION

 Repair, 

modi

fi

 cation and inspection of HiKOKI Power Tools must be carried out by 

a HiKOKI Authorized Service Center.

 

This Parts List will be helpful if presented with the tool to the HiKOKI Authorized 

Service Center when requesting repair or other maintenance.

 

In the operation and maintenance of power tools, the safety regulations and 

standards prescribed in each country must be observed.

Important notice on the batteries for the HiKOKI cordless power tools

Please always use one of our designated genuine batteries. We cannot guarantee the safety 

and performance of our cordless power tool when used with batteries other than these 

designated by us, or when the battery is disassembled and modi

fi

 ed (such as disassembly 

and replacement of cells or other internal parts).

000Book̲GP10DL̲ChS.indb   41

000Book̲GP10DL̲ChS.indb   41

2018/12/06   12:33:16

2018/12/06   12:33:16

Содержание FGP 10DL













































Отзывы: