11
English
2. If liquid leaks onto your skin or clothes, wash well with
clean water such as tap water immediately.
There is a possibility that this can cause skin irritation.
3. If you
fi
nd rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when using the
battery for the
fi
rst time, do not use and return it to your
supplier or vendor.
WARNING
If an electrically conductive foreign object enters the
terminals of the lithium ion battery, a short-circuit may
occur resulting in the risk of
fi
re. Please observe the
following matters when storing the battery.
○
Do not place electrically conductive cuttings,
nails, steel wire, copper wire or other wire in the
storage case.
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 2
).
CHARGING
Before using the driver drill, charge the battery as follows.
1. Connect the charger’s power cord to a receptacle.
2. Insert the battery into the charger.
Firmly insert the battery into the charger till it contacts
the bottom of the charger and checking the polarities
as shown in
Fig. 3
.
Inserting the battery will turn on the charger (the pilot
lamp lights up).
CAUTION
If the pilot lamp does not light up, pull out the power
cord from the receptacle and check the battery
mounting condition.
The pilot lamp goes o
ff
to indicate that the battery is
fully charged.
CAUTION
If the battery is heated due to direct sunlight, etc.,
just after operation, the charger pilot lamp may not
light. At that time cool the battery
fi
rst, then start
charging.
○
Regarding recharging time
Table 1
shows the recharging time required according
to the type of battery.
Table 1 Recharging time (approx. min.) at 20°C
Battery
voltage (V)
Battery capacity (Ah)
1.5 Ah
3.6 V
EBM315
30 min.
NOTE
The recharging time may vary according to the ambient
temperature.
3. Disconnect the charger’s power cord from the
receptacle.
4. Hold the charger
fi
rmly and pull out the battery.
NOTE
After operation, pull out batteries from the charger
fi
rst,
and then store the batteries properly.
SPECIFICATIONS
POWER TOOL
No-load speed (Low/High)
200 / 600 min
–1
Capacity
Drilling
Metal
(Thickness 1.0 mm)
Steel: 5 mm
Aluminum: 5 mm
Driving
Machine screw
5 mm
Wood screw
3.8 mm (diameter) × 38 mm (length)
(Requires a pilot hole)
Rechargeable battery
EBM315: Li-ion 3.6 V (1.5 Ah 1 cell)
Weight
0.45 kg
CHARGER
Model
UC3SFL
Charging voltage
3.6 V
Weight
0.3 kg
STANDARD ACCESSORIES
1
Plus driver bit (No. 2 × 50L) ..........................................1
2
Battery (EBM315) .........................................................1
3
Charger (UC3SFL) .......................................................1
4
Plastic case ..................................................................1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
1. Battery (EBM315)
Optional accessories are subject to change without notice.
APPLICATIONS
○
Driving and removing of machine screws, wood
screws, tapping screws, etc.
○
Drilling of various metals
BATTERY REMOVAL/INSTALLATION
1. Battery removal
Hold the handle tightly and push the battery release
buttons (2 pcs.) to remove the battery (see
Figs. 1
and
2
).
000Book̲DB3DL2̲EE.indb 11
000Book̲DB3DL2̲EE.indb 11
2017/12/06 11:16:28
2017/12/06 11:16:28
Содержание DB 3DL2
Страница 90: ...90 000Book DB3DL2 EE indb 90 000Book DB3DL2 EE indb 90 2017 12 06 11 16 41 2017 12 06 11 16 41 ...
Страница 92: ...92 1 2 3 4 5 000Book DB3DL2 EE indb 92 000Book DB3DL2 EE indb 92 2017 12 06 11 16 42 2017 12 06 11 16 42 ...
Страница 94: ...Back DB3DL2 indd 2 Back DB3DL2 indd 2 2018 02 15 12 09 50 2018 02 15 12 09 50 ...
