manualshive.com logo in svg

High Tech Pet Armor Flex, Руководство по установке

Поделиться
Скачать
High Tech Pet Armor Flex Скачать руководство пользователя страница 8

8 

 

Fig 9 

Fig 10A 

Fig 11 

Fig 10B 

Fig 10C 

STEP 9: Loosen the Top Slider set screws 

Loosen the Top Slider locking set screws on the left and right 
sides of the Top Panel Assembly 

using the 1/8” 

Allen wrench 

provided. If the Top Slider does not immediately release, push it 
up by hand so that it slides to its highest position.  
 
 
 
 
 
 

STEP 10: Insert the patio pet door into your sliding glass door track  

 
Make sure the lock holes in the Top Frame Assembly are facing the inside of your home. Position the pet 
door assembly into your sliding glass door frame by first inserting the pet door Bottom Panel into the 
bottom of your door track so that the Simi-circular groves in the pet door Bottom Panel are placed over 
the sliding rail at the base of your sliding glass door track (Fig 10A). Tilt the pet door assembly up. (Fig 
10B). pull down on the Top Slider. Insert the Top Slider into the top of your door track and release, 
allowing it to move up into the top of the track.  
 
 

STEP 11: Install a House Lock Tab on the 
Top Panel Assembly 

Install a House Lock Tab on the wall side of the pet door 
by screwing 

(2) #6 X ½” round head sheet metal screws 

into the pre-drilled holes on the pet door. Position the 
Tab with the open end pointing downward as shown. 
  
 
 
 

 
 

Содержание Armor Flex

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды