High-End Technology Flying Wing Скачать руководство пользователя страница 7

Страница: 7 / 8

MOTORS and ESCs THAT CAN BE USED

MOTOR

ESC

power

LIPO

Proppellor

4W 2 cells

40 amps

200 Watts

1500 Mah 25c 3S1P

8 x6 folding prop.

5W 2cells

40 amps

200 watts

1800Mah 25C 2200 25C

10 x6 folding prop.

15-10 3 cells

30 amps

200 watts

1800Mah 25C

10 x6 folding prop

15-13 3 cells

30 amps

200 watts

1800 Mah 25C

11 x6 folding prop

FINAL ASSEMBLY

Install the receiver in the fuse. Connect all servo leads to the receiver. Check to make sure
all controls are working. Some adjustments may be needed to obtain the proper control
surface movement.
Check the final balance of the plane.

C.G. 180-195 mm from leading edge ( 185 mm on test model)

Throws:

Set both elevons 5 mm up. This is the neutral position

Elevator up /down 8 mm ( exponential 40%) from neutral position

Aileron 10 mm down 6mm up ( exponential 40%) from neutral position

Содержание Flying Wing









Результаты поиска

Содержание Flying Wing

Отзывы:

Бренды по названию

Популярные бренды

High-End Technology Flying Wing, Руководство пользователя

Результаты поиска

Содержание Flying Wing

Отзывы:

Бренды по названию

Популярные бренды