manualshive.com logo in svg

High-End Technology F16, Инструкция по сборке

Поделиться
Скачать
High-End Technology F16 Скачать руководство пользователя страница 10

Tape the canopy frame to the fuselage so that all sides are flush. 
Drill first a pilot hole 1 -1.5 mm through the front frame (inside look at picture). Now drill a 3 
mm hole same size as the supplied hard wood dowel. Push the dowel in the drilled hole, let it 
stick out approximately 2mm, and glue with 5 minute epoxy thickened with some micro-
balloons. (See picture)   

In the left picture you see the dowel coming out the canopy-frame. In the right picture you see 
rear-end of the canopy frame, we have supply two magnets. One magnet should be glued 
inside the rear-end (back) of the canopy-frame with 5 minute epoxy the other magnet should 
be glued inside the fuselage straight under the magnet in the canopy frame. 

Attention:  Before you trim the edges from the clear abs canopy trial fit it several times 
and assure that it has a good seat (fit).  Make sure is does not put stress on the canopy 
frame. 
 
Now you can glue the clear abs canopy to the canopy frame with 5 minute epoxy. Look 
at the above picture. 

Содержание F16


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды