AMPLIFIER FEATURE DESCRIPTIONS
XXV SERIES AMPLIFIERS
The XXV Juno and XXV Gemini are capable of 4 & 2 Ohms stereo per
All crossovers are fully variable in their respective ranges.
channel, or 4 Ohm mono bridged operation. The XXV Colossus and XXV
Crossover filter slopes are 12 dB/octave for stereo filters, and 24
Maxximus are capable of 4, 2 & 1 Ohms stereo per channel, or 4 & 2 Ohms
dB/octave for mono filters.
A
POWER
LED indicates the powered up and turned on condition.
mono bridged operation. The XXV Thor, XXV Cyclops, XXV Goliath, and
All HiFonics amplifiers feature a comprehensive diagnostic system, with
XXV Sampson are capable of 4, 2 & 1 Ohms.
speaker lead short circuit, thermal over load and amplifier DC faults
Tri-Mode operation with any stereo pair of amplifier channels is possible,
indicated by the
PROTECT
LED’s. The XXV series also features a new
as with all bridgeable amplifiers.
clipping led indicator that changes colors as the severity of the clipped
The input sensitivities for rated output powers are variable from 0.2 volt to
signal increases.
9 volts.
CLASS A/B FRONT MOUNT CONTROL FEATURE DESCRIPTIONS
1
SUBSONIC:
The variable Subsonic filter is fully adjustable from 15Hz to 150Hz.
PARAMETRIC
BASS EQ:
CUT /
BANDWIDTH:
The bandwidth is fully adjustable from narrow to wide.
FREQUENCY:
The frequency is fully adjustable from 40Hz to 400Hz with a selectable X1 or X10 multiplier.
CROSSOVER:
The 2 channel amps have 2 crossover switches. One allows you to select HPF (high pass filter), LP/BP (low pass-band pass filter)
at 12dB or 24dB mono. The second switch allows you to select mono or stereo operation while in LP/BP configuration. The 4 channel amps have
separate CROSSOVER controls for channels 1 / 2 and channels 3/4.
INPUT MODE:
In the Ch2 position, all 4 amplifier channels derive their input signals from Ch1 & Ch2 Line Inputs (RCA). When set to Ch4,
channels 1, 2, 3 and 4 receive input signals from Ch1, Ch2, Ch3 and Ch4 Line Inputs (RCA).
SUBSONIC:
The variable Subsonic filter is fully adjustable from 15Hz to 35Hz.
LOW PASS FILTER:
The low pass filter is fully adjustable from 35Hz to 250Hz.
PARAMETRIC
BASS EQ:
BOOST:
The bass boost is fully adjustable from 0dB to 10db.
BANDWIDTH:
The bandwidth is fully adjustable from narrow to wide.
FREQUENCY:
The frequency is fully adjustable from 30Hz to 100Hz.
MASTER / SLAVE:
The mono amps (XXVThor / XXVCyclops / XXVGoliath, XXVSampson) allow you to electronically “link” two amps together
so that you can power and single subwoofer with two amplifiers.
BALANCED INPUT:
Accepts balanced line inputs from 0.2 volts to 18 volts for the optional MMBLD-1 balanced line driver.
LINE INPUT:
Accepts unbalanced RCA inputs from 0.2 volts to 9 volts.
LINE OUTPUT:
The unbalanced RCA outputs are set the same as the CROSSOVER switch on the front mount control and end panel.
LEVEL:
The input level control allows you to match the amplifier input sensitivity to the output level of the RADIO/CD source from 0.2 Volts to 9
volts when using unbalanced (RCA) and 0.2 volts to 18 volts with the balanced input.
PHASE SHIFT:
The Phase Shift is fully adjustable from 0 to 180 degrees.
SYSTEM DIAGNOSTICS:
The amplifier has built-in monitoring devices and protection circuits that monitor all vital functions of the amplifier.
The diagnostics light do not come on to indicate there is a failure, they come on when they detect an improper operation.
THERMAL:
The amp has an internal temperature sensor that will automatically shut off the amp if it reaches dangerous temperature levels and
the LED will be Amber in color.
DC PROTECT (Short Circuit):
In the unlikely event the amp should internally fail, the amp will shut down to prevent a DC voltage output to the
speakers or sub and the LED will be Red in color.
Clipping:
While adjusting the amplifier the LED may light up Green indicating Pre-Clip, Amber indicating Soft-Clip or Red indicating Clip. These
indicators give the user a chance to identify incorrect settings or high distortion before it is damaging to the equipment allowing them to correct the
volume or settings.
REMOTE:
All XXV amps have DIN cable bass remote jacks labeled INPUT. The XXVR-1 Bass Remote Module plugs
into the INPUT jack and allows you to adjust the Bass Boost from 0 to 10dB.
BOOST:
The bass cut / boost is fully adjustable from -10dB to 10db.
D-CLASS SIDE MOUNT CONTROL FEATURE DESCRIPTIONS
SHARED CONTROL FEATURE DESCRIPTIONS
