Setup
Quick Start
Installation Guide
The illustrations below describe the various controls. Refer to
the illustration that matches your amplifier.
The gain control purpose is to match
the output of your source signal to the
amplifier. Refer to the section B below for
detailed instructions.
This switch will set the amplifier to have
a full frequency output or to filter out high
or low frequencies. The NA1-400.2 offers
either a bandpass or a high pass filter.
The Low Pass Filter will cut off the
frequencies above the setting. The High
Pass Filter will cut off the frequencies
below the setting.
The Boost Switch will increase the signal
12dB at 45Hz. Be aware this setting can
cause distortion if the gain is not set
properly.
The Subsonic Filter will cut off the
frequencies below the setting. If using
with a subwoofer the settin should be kept
between 15-25Hz.
1.
If possible, with the source unit off, confirm that the primary volume control is
turned down (counter clockwise).
2.
Turn on the source unit (CD, or MP3 player). Re-confirm that the volume is
turned down. Make sure the source unit controls; balance, fader, bass and
treble are all set to center or “0” adjustment. Make sure that the green LED on
the end of the amplifier is illuminated.
3.
Play a clean musical selection of which you are very familiar. CD is preferred.
Do not use radio signals for level setting. Hit play and start turning the volume
of the source unit up.
4.
Stop increasing the source unit volume when you reach 3/4 (about 75%) or until
you hear speakers begin to slightly start producing distortion.
5.
Increase the amplifier gain (clockwise) until distortion is heard, then back
the level down (counter clockwise) until the distortion is eliminated. Small
adjustments may need to be made to balance the levels of multiple amplifiers.
Settings
A
This is a critical step to insure your amplifier
is properly adjusted to match the signal
output level of your source unit.
THIS IS NOT A VOLUME CONTROL!
Level Setting
B
WARRANTY
Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from
defects in material and workmanship for a period of one (1) year from the date of purchase.
Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty
period. Components that prove to be defective in materials and workmanship under proper installation
and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was
purchased. A photocopy of the original receipt must accompany the product being returned. The
costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics
USA Inc. This warranty is limited to defective parts and specifically excludes any incidental or
consequential damages connected therewith. To view the full warranty, please visit the website.
The information contained within this document is intended to offer some basic guidelines
for a few of the most common installations. More complex audio systems should be
installed by a competent professional. Additional installation information available at
www.maxxsonics.com
Hifonics products are designed and engineered in the USA by
www.maxxsonics.com
Congratulations on your choice of a Hifonics amplifier.
This “Quick Start Installation” guide is meant to help you
“hook up” and play music. For more detailed information,
on system setting, speaker and subwoofer configuration
and full specifications by model visit the website,
http://hifonics.com/manuals.html
HF TPS-A QSG 01 - rev1
TPS-A500.2
TPS-A350.4
TPS-A500.1
TPS-A600.5
FRONT
L
R
REAR
L
R
INPUT
L
R
GAIN
MIN
MAX
LPF
50Hz 150Hz
SUBSONIC
15Hz 50Hz
SUBSONIC
15Hz 300Hz
FRONT
GAIN
MIN
MAX
REAR
GAIN
MIN
MAX
BOOST
0dB
12dB
X-OVER
LPF
FULL
FRONT
X-OVER
HPF
FULL
REAR
X-OVER
HPF
FULL
INPUT
R
L
FRONT
R
L
REAR
R
L
INPUT
R
L
GAIN
MIN
MAX
LPF
50Hz 150Hz
SUBSONIC
15Hz 50Hz
GAIN
MIN
MAX
F GAIN
MIN
MAX
R GAIN
MIN
MAX
LPF
50Hz 300Hz
HPF
HPF
15Hz 300Hz
BOOST
0dB
12dB
X-OVER
BPF
HPF
FRONT
X-OVER
HPF
FULL
REAR
X-OVER
HPF
FULL
1
3
3
2
2
1
1
3
4
5
TPS-A500.1
TPS-A500.2
2
1
2
1
X-OVER
HP OFF LP
INPUT
L
R
LEVEL
HP
LP
9V 0.2V 15Hz 300Hz 50Hz 300Hz
LEVEL
9V 0.2V
FRONT
X-OVER
HP
OFF
LEVEL
9V 0.2V
REAR
X-OVER
HP
OFF
INPUT
FRONT
L
R
REAR
L
R
BOOST
0dB 12dB
INPUT
L
R
LEVEL
9V 0.2V
LPF
50Hz 150Hz
SUBSONIC
15Hz 50Hz
TPS-A350.4
TPS-A600.5
1
3
4
5
1
2
3
4
5
GAIN Adjustment
X-OVER Switch
Frequencies
Adjustment
SUBSONIC Adjustment
BOOST Switch
Visit Hifonics.com
