Hifionics Zeus ZXI150.4, Руководство пользователя

Страница: 4 / 14

AMPLIFIER FEATURE DESCRIPTIONS
ZEUS ZXi AMPLIFIERS:
CAUTION: DO NOT OPERATE ANY AMPLIFIER BELOW THE INTENDED IMPEDANCE. YOU Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation
! !
WILL CAUSE DAMAGE TO THE AMPLIFIER THAT WILL NOT BE COVERED UNDER THE
except the 5 channel which is capable of 1-Ohm on channel 5.
WARRANTY PRINTED IN THE BACK OF THE MANUAL. 2 & 4 Channel amps are capable of 4 !
The input sensitivities for rated output powers are variable from 0.2 volts to 6 volts.
!
All crossovers are fully variable in their respective ranges.
and 2-Ohms wired stereo and 4-Ohms wired mono bridged. The 5 channel amp is capable of 4,
!
Crossover filters are 12dB/Octave.
2 and 1-Ohm operation on the 5th channel ONLY.
!
A POWER LED indicates the powered up and turned on condition.
!
All Hifonics amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit,
and amplifier DC faults indicated by the red “ PROTECT” LED.
2
ZXi60.4+1K 5-CHANNEL AMPLIFIERS
The 4 channel amps have the same features as the 2 channel models accept that there are 2 sets of
controls.
1 set for channels 1 & 2 and 1 set for channels 3 & 4.
In addition, the 4 channel models have a
Mode switch. Switch to 2 channel if you only have 1 set of
RCA’s in CH 1/2 and the unit will automatically supply signal to channels 3/4. Select 4 channel if you
are providing RCA’s to channels 1/2 and 3/4.
The
X-OVER slide switch selects the internal crossover functions:
-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting
simplifying daisy chaining of amplifiers.
-HP: Selects the built in HIGH PASS filter, variable from 10 Hz to 15kHz.
-FULL: Bypasses all crossovers for full frequency range operation.
-LP/BP: Selects the built in LOW PASS , variable from 30 Hz to 150Hz.
LINE INPUT : The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.
LINE OUTPUT : The line output passes through signal from the line inputs which allows you to daisy
chain multiple amplifiers from one signal.
BASS EQ: Fixed 45Hz bass boost variable from 0dB to 10dB.
Note that the LOW PASS signal is MONO.
-In the LP/BP position, the HIGH PASS filter acts as a
subsonic filter.
-When the LP/BP mode is selected, a 0 to +10dB, at 45Hz,
BASS EQ is also switched in.
ZXi40.4 / ZXi80.4 / ZXi150.4 4-CHANNEL AMPLIFIERS
The X-OVER slide switch selects the internal crossover functions:
-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting
simplifying daisy chaining of amplifiers.
-HP: Selects the built in HIGH PASS filter, variable from 10Hz to 15kHz.
-FULL: Bypasses all crossovers for full frequency range operation.
-LP/BP: Selects the built in LOW PASS , variable from 30Hz to 150Hz.
BASS EQ: Fixed 45Hz bass boost variable from 0dB to 10dB.
LINE INPUT : The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.
LINE OUTPUT : The line output passes through signal from the line inputs which allows you to daisy
chain multiple amplifiers from one signal.
Note that the LOW PASS signal is MONO.
-In the LP/BP position, the HIGH PASS filter acts as a
subsonic filter.
-When the LP/BP mode is selected, a 0 to +10dB, at 45Hz,
BASS EQ is also switched in.
ZXi200.2 2-CHANNEL AMPLIFIERS
HP FULL LP/BP
10Hz 15KHz 30Hz 150Hz 0dB 10dB
6V 0.2V
REMOTE
HI PASS LOW PASS BASS EQ LEVEL POWER X-OVER
PROTECT
LINE INPUT
L
R
L
R
LINE OUT
LINE INPUT REMOTE
POWER
PROTECT
LINE OUT
HI FULL LP/BP
HI FULL LP/BP
6V 0.2V 10Hz-15KHz 30Hz-150Hz 0dB-10dB
HI PASS LOW PASS BASS EQ LEVEL
X-OVER
1/2 CH
6V 0.2V 10Hz-15KHz 30Hz-150Hz 0dB-10dB
X-OVER
3/4 CH
HI PASS LOW PASS BASS EQ LEVEL
MODE
CH2-CH4
L
R
L
R
L
R
CH1/2 CH3/4
The ZXi60.4+1K has three sets of inputs:
Line inputs on RCA jacks for channel pairs 1&2, 3&4, and MONO channel 5. These inputs can be used in
various combinations, to suit the application, depending on the settings of the INPUT MODE switch, and
the X-OVER switches for channels 1&2, and channels 3&4, respectively.
INPUT MODE slide switch:
- In the CH2 position, ALL five amplifier inputs are selected from the CH1/CH2 RCA jacks. Channel 5
receives a mono mixed signal.
- In the
4CH position, channel pair 1&2 receive input signal from RCA jacks CH1 and CH2, and channel
pair 3&4 receive input signal from RCA jacks CH3 and CH4. A mono mixed signal from these four RCA
jacks are also fed to channel 5.
- When
5CH DISCRETE is selected, each channel receives an input signal from its respective input RCA
jack. Channel 5 has two jacks on its LINE INPUT, which are summed together.
CH1/2 X-OVER slide switch:
- HI: Selects the HIGH PASS filter, variable from 10Hz to 15KHz.
- FULL: Sets this pair to full range operation.
CH3/4 X-OVER slide switch:
- HI: Selects the HIGH PASS filter, variable from 10Hz to 15KHz.
- FULL: Sets this pair to full range operation.
-LP/BP: Selects the built in LOW PASS , variable from 30 Hz to 150Hz.
CH 5:
- The channel 5 functions were chosen to be very specific to mono bass operation, and not switchable:
- The
LOW PASS filter has a variable range from 30 Hz to 150 Hz.
- The BASS EQ gives a bass boost, 0 to +10 dB, at 45 Hz.
REMOTE
POWER
PROTECT
LINE INPUT
CH1
CH2
CH3
CH4
5CH
10Hz 15Khz 10Hz 15Khz
HI PASS
6V 0.2V
LEVEL
6V 0.2V
LEVEL LOW PASS
30Hz 150Hz
HI PASS
MODE
Ch2 Ch4 Ch5
X-OVER
CH3/4
0dB-10dB 30Hz 150Hz 6V 0.2V
BASS EQ LOW PASS LEVEL
HI FULL
HI FULL BP
X-OVER
CH1/2