Solar Module Installation Manual
2
Thank You
for selecting
HHV SOLAR Photovoltaic Modules.
Please read and comprehend
this manual completely before installing the Solar PV Modules.
In order to obtain a trouble free operation it is necessary to follow the instructions
described in this manual.
A. LIMITATION OF LIABILITY
HHV Solar shall not be held responsible for damages of any kind, including without
limitation bodily harm, injury and property damage, relating to module handling, system
installation or compliance or non‐compliance with the instructions set forth in this manual.
B. SAFETY PRECAUTIONS
Warning:
All instructions should be read and understood before attempting to open the box
and install, wire, operate and/or maintain the module. Module interconnects pass direct
current (DC) when exposed to sunlight or other light sources. Contact with electrically active
parts of the module, such as terminals, can result in injury or death, whether the module is
connected or disconnected.
The details described in this manual are applicable for the photovoltaic modules of family
type:
HSTXY24xxxZ (with 72 cells, 6”, xxx = 240 ‐ 325 in 5W‐Steps)
HSTXY24xxxZ (with 66 cells, 6”, xxx = 230 ‐ 280 in 5W‐Steps)
HSTXY24xxxZ (with 60 cells, 6”, xxx = 200 ‐ 270 in 5W‐Steps)
HSTXY12xxxZ (with 54 cells, 6”, xxx = 180 ‐ 245 in 5W‐Steps)
HSTXY12xxxZ (with 48 cells, 6”, xxx = 160 ‐ 215 in 5W‐Steps)
HSTXY12xxxZ (with 36 cells, 6”, xxx = 120 ‐ 165 in 5W‐Steps)
The families mentioned above are having the following codification,
Ex : HST
XY
24280
Z
X= Cell Supplier
Y= Cell Size (Full/Cut cell)
Z= Cell type (Mono/Multi)
H
S
T
X
Y
24
280
Z
HHV Solar Technologies
Cell
Supplier
Cell
Size
Battery
Charging
Voltage
Wattage
Cell
type
Note: The information provided in this manual is subject to revision without prior notice for continual improvement.
Solar Module Installation Manual
C. Components of a Solar Module
The Modules are classified for the application C
•
Hazardous voltage (IEC61730: higher than 50V DC ; EN 61730: higher than 120V),
hazardous power applications (higher than 240W) where general contact access is
anticipated ( modules
application class are considered to meet the requirements for safety class II )
•
The objective of this manual is to provide the customer(s) clear instructions on how to
mount the PV modules to
requirements.
•
Further, please also consult the local authorities
before taking up or mounting of the PV modules and ensure that the mounting
instructions described in
Module
classified for the application Class –A :
Hazardous voltage (IEC61730: higher than 50V DC ; EN 61730: higher than 120V),
hazardous power applications (higher than 240W) where general contact access is
anticipated ( modules qualified for safety thorough EN IEC 61730-1 and
application class are considered to meet the requirements for safety class II )
The objective of this manual is to provide the customer(s) clear instructions on how to
the PV modules to ensure compliance with certification and regulatory
Further, please also consult the local authorities (if there any statutory requirement)
before taking up or mounting of the PV modules and ensure that the mounting
instructions described in this manual meet their requirements.
3
Hazardous voltage (IEC61730: higher than 50V DC ; EN 61730: higher than 120V),
hazardous power applications (higher than 240W) where general contact access is
1 and -2 within this
application class are considered to meet the requirements for safety class II )
The objective of this manual is to provide the customer(s) clear instructions on how to
ensure compliance with certification and regulatory
(if there any statutory requirement)
before taking up or mounting of the PV modules and ensure that the mounting
