Enter menu Set2, by turning the knob select the combination of
days which is required. Confirm by briefly pressing the knob.
Programming always starts at 00 hours. By
turning the knob clockwise, you can move
through the time line. Press the knob at the
point from which you want to start with heating
to comfort temperature. By turning the knob
now there will be points visible which represent
the hours of heating to economy temperature.
By turning the knob anti clockwise the points
are erased. Pressing the knob switches
between economy and comfort temperature.
After programming of the whole day has been
finished, the thermostat shows you OK. When
the knob is pressed all settings are saved.
Set3 - Service menu
In this menu service parameters can be changed. Under common
circumstances it is not necessary to change any of those
parameters.
Hysteresis is the accuracy to which the
temperature is regulated. The setting is done
via the HYst item in the adjustment menu.
Turning the knob lets select you one of the
following accuracy ranges: ±0.1°C to ±1°C
(factory setting: ±0.2°C)
Example: If the accuracy is adjusted to
±0.5°C and the temperature is set to 24°C,
the thermostat switches the heating on
when the temperature drops below 23.5°C
and switches it off if the temperature goes
above 24.5°C. In reality the temperature
scatter can be slightly higher because of the
temperature persistence of the room.
Warning: Too high accuracy can cause the
heating to turn on and off to frequently.
The item Stby sets the temperature which
will be kept in the case of switching off ther
thermostat (item OFF). The Stby temperature
is always at least 3°C higher than ALLo. The
value of the Stby temperature does not have
to be set higher than the t Lo tmperature.
The t Lo item is the lower limit to which
economical temperature can be set.
The t Hi item is the upper limit to which the
comfort temperature can be set.
AL Lo is the lower critical temperature. When
the temperature drops under the preset
value, the thermostat sends an alarm report
to the receiver and this state is indicated
by a permanently lit (!) symbol. The ALLo
- temperature is always at least 3°C lower
than t Lo.
AL Hi is the upper critical temperature. When
the temperature increases above the preset
value, the thermostat sends an alarm report
to the receiver and this state is indicated
by a permanently lit (!) symbol. The ALHi
temperature is always at least 3°C higher
than tHi.
TP-155 Wireless programmable indoor thermostat
The TP-155 is a wireless programmable indoor thermostat with a weekly heating
schedule. It can regulate the
economical or comfort temperature
inside residential buildings. It offers a
few programmable modes. Every
mode regulates pre-set temperatures
(Comfort, Economy, Holiday, and
Party). The thermostat is able to
measure the thermal inertia inside the
premises and adjust the weekly
schedule
for the requested
temperature to be reached at the pre-
set time.
Figure 1
: 1- knob (encoder) combined with button; 2- tab
Thermostat installation
The product can only be used in an indoor environment. Install the thermostat 1.5
m above the floor in a place where there is good natural air circulation. Don´t install
the thermostat where the measuring can be influenced by drafts, sunlight, heaters or
any other effects. Avoid mounting the thermostat on metal objects or metal bases
which block radio communication.
1. By pressing the tab (by screwdriver for instance) release the front part of the
thermostat.
2. Install the rear part of the thermostat at the chosen place (tab down).
3. Insert the batteries, the polarity is marked on the plastic.
4. Put back the front thermostat part and close it.
Enrolling the thermostat
Install and connect the receiving unit to the heating appliance. If the receiver has
been bought independently, you have to enroll the thermostat to it first. Open the
enrollment mode on the receiver (see its manual) and insert the batteries into the
thermostat or press and hold the knob for 5s. In both cases the thermostat will send
an enrollment signal. The text
LRn
appears on the LCD display when the enrolling
procedure (with AC-116 only) has been done successfully.
Symbols on the LCD:
Figure 2: 1 – Symbols for
comfort and economical
temperatures; 2 – The days of
the week; 3 – Locking the
thermostat; 4 – Alarm tempe-
rature
–
limits / loss of
communication; 5 – Heating
ON / OFF; 6 – Holiday; 7 – Party;
8 – Heating times; 9 – Symbols
for showing temperature time
and texts; 10 – Low battery
Settings and programming
Do the complete settings using the knob – encoder. By pressing the knob 2 sec
enter the programming mode.
General rules for programming:
1. Flashing of any icon on the LCD allows changing the option(s) or choosing a
next item.
2. Perform choosing or changing by turning the knob (turning the knob is possible
from left to right and vice versa).
3. Confirm the selection or change by briefly pressing the knob.
4. When the value of an item has been changed, then after this briefly press the
knob and the changes are saved. Then the thermostat goes to the next item in
the programming menu.
5. After the setting / change of the chosen items, select the parameter „OK“, in the
menu. By short pressing the system returns back to the previous menu (up to
the main menu).
6. If there is no manipulation of the knob for 30 sec, it returns you back to the
previous menu automatically.
The basic menu has 7 groups of settings.
MA
n
Manual mode
LO
c
Locking the thermostat
OF
F
Switching off the thermostat
SE
t1
Temperature, date and time settings
SE
t2
Weekly schedule setting
SE
t3
Service menu
OK
Saving the parameters and leaving the service menu
1. MAn – manual mode
The temperature is set manually regardless of the weekly
schedule and is kept. Enter the menu and press the knob on
the item
Man,
the option ON (switched on) appears. By
turning the knob select the requested state and confirm by
pressing. The temperatures
tLo
and
tHi
determine the regulation range pre-
programmed in the service menu SE t3, in which you can select the temperature by
turning the knob. Choose the requested temperature. If the chosen temperature is
lower than the required temperature, the thermostat shows the symbol
(▲)
on its
LCD display. By entering the menu
Man
and confirming the option
OFF
, manual
mode is terminated.
2. LOc – Locking the thermostat
To protect the thermostat against unwanted manipulation you
can lock the thermostat. Enter the menu and press the knob
on the item
LOc,
the options
ON/OFF
appear. By turning the
knob select the requested state and confirm by pressing.
Choosing
ON
enables the function
Lock
, and blocks thermostat control. To unlock
the thermostat choose the option
OFF.
Locking the thermostat is indicated on the
LCD by the
symbol.
3. OFF – Switching off the thermostat
The thermostat can be switched off by the option
OFF
.
Enter the menu and press the knob on the item
OFF,
the
options
ON/OFF
appear. By turning the knob select the
requested state and confirm by pressing. Choosing
ON
enables the function
OFF
, and switches off the thermostat. This is indicated on the
LCD by the text
OFF
. Although the thermostat has been switched off, it still
measures and detects the antifreeze temperature (see SE t3, Stby). To unlock the
thermostat enter the menu and choose the option
OFF.
When the knob is pressed
the thermostat will be unlocked.
4. Set1 - Temperature, date and time settings
In the Set1 menu the comfort temperature ( ), the economy
temperature ( ), the temperature for Holiday mode ( ), and
the data and time can be preset. Enter the menu
Set1
, and
on the LCD the symbol of the economy temperature starts
flashing. By turning the knob select the requested item ( , or ), by pressing the
knob the symbols for temperature start flashing and again by turning the knob set the
required temperature and by repeatedly pressing the knob confirm this setting. The
last item serves for setting the current time. It indicates using flashing symbols of the
days of the week. By pressing you enter the current time setting. It starts with the
year. Pressing gets it flashing, and by turning the knob set the year, by pressing
again it saves the setting and then you continue the same way in setting the current
month, day, hour and minute. Then by pressing the knob after the minute setting the
values are saved and the thermostat is back in the menu
Set1
. Select the item
OK
to
leave this menu.
5. SEt2 – Weekly schedule setting
The heating program for switching the comfort and the economy temperatures can
be set for every single day independently (Mo - Monday, Tu - Tuesday, We -
Wednesday, Th - Thursday, Fr - Friday, Sa - Saturday, Su - Sunday) or it can be
split into working days and the weekend. There is one more option - the same
settings for all days with no difference.
Enter the menu
Set2
, and by turning the knob select the combination of days which
is required. Confirm by briefly pressing the knob. It enters the programming of heating
time periods when the thermostat switches between the day temperature and the
night temperature.
Programming always starts at 00 hrs. By turning the knob
clockwise, you can move through the time line. Press the
knob at the point from which you want to start with the
heating to the comfort temperature. The symbol changes
to the . Now by turning the knob clockwise the points
appear which represent the hours for which heating is
performed to the economy temperature. By turning the
knob anti-clockwise the points are erased. Pressing the
knob more switches the economy temperature to the
comfort temperature. By repeating this procedure the
comfort and economy temperatures can be set for a
selected day (or for a group of a few days). After the
programming of the whole day has been finished, the
thermostat shows you
OK
. When the knob is pressed, all
settings are saved.
6. SEt3 – Service menu
The service parameters can be pre-programmed here. In normal mode it is not
necessary to change those parameters. The Service menu includes 9 items. Open
by scrolling the knob to the requested item and by pressing the knob to enter the
programming mode. Select the value again by scrolling the knob. Confirm it by
pressing the knob and it returns you back to the service menu.
TP-155 Wireless programmable indoor thermostat
1 / 2
MMC51701
TP-150 wireless indoor thermostat
The TP-150 is a wireless indoor thermostat. It serves for the measuring and
regulation of temperature. The temperature is set by the knob. The
thermostat regulates a pre-set temperature 24hrs per day.
The thermostat can be locked against unwanted manipulation. As well
as the regulation of temperature it can also report reaching the high and
low temperature limits.
Figure1
: 1 - knob (encoder) combined with button 2 - tab
Thermostat installation
The product can only be used in an indoor environment. Install the
thermostat 1.5 m above the floor in a place where there is good natural air
circulation. Don´t install the thermostat where the measuring can be
influenced by drafts, sunlight, heaters or any other effects. Avoid mounting
the thermostat on metal objects or metal bases which block radio
communication.
1. By pressing the tab (by screwdriver for instance) release the front part of
the thermostat.
2. Install the rear part of the thermostat at the choose place (tab down).
3. Insert the batteries; the polarity is marked on the plastic.
4. Put back the front thermostat part and close it.
Enrolling the thermostat
Install and connect the receiving unit to the heating appliance. If the
receiver has been bought independently, you have to enroll the thermostat to
it first. Open the enrollment mode on the receiver (see its manual) and insert
the batteries into the thermostat or press and hold the knob for 5s. In both
cases the thermostat will send an enrollment signal. The text
LRn
appears on
the LCD display when the enrolling procedure (with AC-116 only) has been
done successfully.
Symbols on the LCD:
Figure 2: 1 – Symbols of temperature and texts; 2 – Locking the thermostat;
3 – Alarm temperature-limits / Loss of communication; 4 – Heating ON / OFF;
5 – Low battery
Settings and programming
Do the complete settings using the knob – encoder. By pressing the knob 2
sec enter the programming mode.
General rules for programming:
1. Flashing of any icon on the LCD allows changing the option(s) or
choosing a next item.
2. Perform choosing or changing by turning the knob (turning the knob is
possible from left to right and vice versa).
3. Confirm the selection or change by briefly pressing the knob.
4. When the value of an item has been changed, then after this briefly press
the knob and the changes are saved. Then the thermostat goes to the
next item in the programming menu.
5. After the setting / change of the chosen items, select the parameter „OK“,
in the menu. By short pressing the system returns back to the previous
menu (up to the main menu).
6. If there is no manipulation of the knob for 30 sec, it returns you back to
the previous menu automatically.
The basic menu has 4 groups of settings.
LO
c
Locking the thermostat
OF
F
Switching off the thermostat
SE
t3
Service menu
OK
Saving the parameters and leaving the service menu
1. LOc – Locking the thermostat
To protect the thermostat against unwanted manipulation
you can lock the thermostat. Enter the menu and press
the knob on item
LOc
, the options
ON/OFF
appear. By
turning the knob select the requested state and confirm
by pressing. Choosing
ON
enables the function
Lock
, and blocks thermostat
control. To unlock the thermostat choose the option
OFF.
Locking the
thermostat is indicated on the LCD by the
symbol.
2. OFF – Switching off the thermostat
The thermostat can be switched off by the option
OFF
.
Enter the menu and press the knob on the item
OFF,
the options
ON/OFF
appear. By turning the knob select
the requested state and confirm by pressing. Choosing
ON
enables the function
OFF
, and switches off the thermostat. This is
indicated on the LCD by the text
OFF
. Although the thermostat has been
switched off, it still measures and detects the antifreeze temperature (see SE
t3, Stby). To unlock the thermostat enter the menu and choose the option
OFF
. When the knob is pressed the thermostat will be unlocked.
3. SEt3 – Service menu
The service parameters can be pre-programmed here. In a normal mode it is not
necessary to change those parameters. The Service menu includes 8 items. Open
by scrolling the knob to the requested item and by pressing the knob enter the
programming mode. Select the value again by scrolling the knob. Confirm it by
pressing the knob and it returns you back to the service menu.
HYst
is an item, where you can program the range of
the switching thresholds around the requested
temperature (hysteresis). The range can be set with a
0.1°C step from 0.1°C to 1°C. (Default setting
±
0.2°C)
Example:
With a set accuracy of ±0.
5˚C
a temperature of
24°C
will be kept this
way, at 23.
5°C it starts heating and at 24
.
5°C
it
stops heating.
In real conditions
regulation could have
a much bigger temperature scatter because of the thermal
inertia in
the
heated
premises.
Warning: An over-narrow pre-programmed hysteresis range could perform
on/off switching of the heating very often.
The item
Stby
sets the temperature which will be kept
in the case of switching off the thermostat (item
OFF
).
The
Stby
temperature is always at least 3°C higher
than
ALLo.
The value of the
Stby
temperature does
not have to be set higher than the
t Lo
temperature.
The
t Lo
item is the lower limit to which economical
temperate can be set.
The
t Hi
item is the upper limit to which the comfort
temperature can be set.
AL Lo
is the lower critical temperature. When the
temperature drops under the pre-set value, the
thermostat sends an alarm report to the receiver and
this state is indicated by a permanently lit (
!
) symbol.
The
ALLo
temperature is always at least 3°C lower
than
tLo
.
AL Hi
is the upper critical temperature. When the
temperature increases above the pre-set value, the
thermostat sends an alarm report to the receiver and
this state is indicated by a permanently lit (
!
) symbol.
The
ALHi
temperature is always at least 3°C higher
than
tHi.
For a reset to factory default settings the
RES
item is
used
.
After you enter the menu and press the knob on
the
RES
item
ON/OFF
appears. By scrolling the knob
select
ON,
and press the knob. Then a RESET will be
done.
When the reset is finished, a 20°C temperature
is pre-set.
By pressing the knob when the thermostat shows you
OK
you leave the service menu and return to the basic
thermostat menu.
TP-150 wireless indoor thermostat
1 / 2
MMC51601
TP-150 wireless indoor thermostat
The TP-150 is a wireless indoor thermostat. It serves for the measuring and
regulation of temperature. The temperature is set by the knob. The
thermostat regulates a pre-set temperature 24hrs per day.
The thermostat can be locked against unwanted manipulation. As well
as the regulation of temperature it can also report reaching the high and
low temperature limits.
Figure1
: 1 - knob (encoder) combined with button 2 - tab
Thermostat installation
The product can only be used in an indoor environment. Install the
thermostat 1.5 m above the floor in a place where there is good natural air
circulation. Don´t install the thermostat where the measuring can be
influenced by drafts, sunlight, heaters or any other effects. Avoid mounting
the thermostat on metal objects or metal bases which block radio
communication.
1. By pressing the tab (by screwdriver for instance) release the front part of
the thermostat.
2. Install the rear part of the thermostat at the choose place (tab down).
3. Insert the batteries; the polarity is marked on the plastic.
4. Put back the front thermostat part and close it.
Enrolling the thermostat
Install and connect the receiving unit to the heating appliance. If the
receiver has been bought independently, you have to enroll the thermostat to
it first. Open the enrollment mode on the receiver (see its manual) and insert
the batteries into the thermostat or press and hold the knob for 5s. In both
cases the thermostat will send an enrollment signal. The text
LRn
appears on
the LCD display when the enrolling procedure (with AC-116 only) has been
done successfully.
Symbols on the LCD:
Figure 2: 1 – Symbols of temperature and texts; 2 – Locking the thermostat;
3 – Alarm temperature-limits / Loss of communication; 4 – Heating ON / OFF;
5 – Low battery
Settings and programming
Do the complete settings using the knob – encoder. By pressing the knob 2
sec enter the programming mode.
General rules for programming:
1. Flashing of any icon on the LCD allows changing the option(s) or
choosing a next item.
2. Perform choosing or changing by turning the knob (turning the knob is
possible from left to right and vice versa).
3. Confirm the selection or change by briefly pressing the knob.
4. When the value of an item has been changed, then after this briefly press
the knob and the changes are saved. Then the thermostat goes to the
next item in the programming menu.
5. After the setting / change of the chosen items, select the parameter „OK“,
in the menu. By short pressing the system returns back to the previous
menu (up to the main menu).
6. If there is no manipulation of the knob for 30 sec, it returns you back to
the previous menu automatically.
The basic menu has 4 groups of settings.
LO
c
Locking the thermostat
OF
F
Switching off the thermostat
SE
t3
Service menu
OK
Saving the parameters and leaving the service menu
1. LOc – Locking the thermostat
To protect the thermostat against unwanted manipulation
you can lock the thermostat. Enter the menu and press
the knob on item
LOc
, the options
ON/OFF
appear. By
turning the knob select the requested state and confirm
by pressing. Choosing
ON
enables the function
Lock
, and blocks thermostat
control. To unlock the thermostat choose the option
OFF.
Locking the
thermostat is indicated on the LCD by the
symbol.
2. OFF – Switching off the thermostat
The thermostat can be switched off by the option
OFF
.
Enter the menu and press the knob on the item
OFF,
the options
ON/OFF
appear. By turning the knob select
the requested state and confirm by pressing. Choosing
ON
enables the function
OFF
, and switches off the thermostat. This is
indicated on the LCD by the text
OFF
. Although the thermostat has been
switched off, it still measures and detects the antifreeze temperature (see SE
t3, Stby). To unlock the thermostat enter the menu and choose the option
OFF
. When the knob is pressed the thermostat will be unlocked.
3. SEt3 – Service menu
The service parameters can be pre-programmed here. In a normal mode it is not
necessary to change those parameters. The Service menu includes 8 items. Open
by scrolling the knob to the requested item and by pressing the knob enter the
programming mode. Select the value again by scrolling the knob. Confirm it by
pressing the knob and it returns you back to the service menu.
HYst
is an item, where you can program the range of
the switching thresholds around the requested
temperature (hysteresis). The range can be set with a
0.1°C step from 0.1°C to 1°C. (Default setting
±
0.2°C)
Example:
With a set accuracy of ±0.
5˚C
a temperature of
24°C
will be kept this
way, at 23.
5°C it starts heating and at 24
.
5°C
it
stops heating.
In real conditions
regulation could have
a much bigger temperature scatter because of the thermal
inertia in
the
heated
premises.
Warning: An over-narrow pre-programmed hysteresis range could perform
on/off switching of the heating very often.
The item
Stby
sets the temperature which will be kept
in the case of switching off the thermostat (item
OFF
).
The
Stby
temperature is always at least 3°C higher
than
ALLo.
The value of the
Stby
temperature does
not have to be set higher than the
t Lo
temperature.
The
t Lo
item is the lower limit to which economical
temperate can be set.
The
t Hi
item is the upper limit to which the comfort
temperature can be set.
AL Lo
is the lower critical temperature. When the
temperature drops under the pre-set value, the
thermostat sends an alarm report to the receiver and
this state is indicated by a permanently lit (
!
) symbol.
The
ALLo
temperature is always at least 3°C lower
than
tLo
.
AL Hi
is the upper critical temperature. When the
temperature increases above the pre-set value, the
thermostat sends an alarm report to the receiver and
this state is indicated by a permanently lit (
!
) symbol.
The
ALHi
temperature is always at least 3°C higher
than
tHi.
For a reset to factory default settings the
RES
item is
used
.
After you enter the menu and press the knob on
the
RES
item
ON/OFF
appears. By scrolling the knob
select
ON,
and press the knob. Then a RESET will be
done.
When the reset is finished, a 20°C temperature
is pre-set.
By pressing the knob when the thermostat shows you
OK
you leave the service menu and return to the basic
thermostat menu.
TP-150 wireless indoor thermostat
1 / 2
MMC51601
TP-150 wireless indoor thermostat
The TP-150 is a wireless indoor thermostat. It serves for the measuring and
regulation of temperature. The temperature is set by the knob. The
thermostat regulates a pre-set temperature 24hrs per day.
The thermostat can be locked against unwanted manipulation. As well
as the regulation of temperature it can also report reaching the high and
low temperature limits.
Figure1
: 1 - knob (encoder) combined with button 2 - tab
Thermostat installation
The product can only be used in an indoor environment. Install the
thermostat 1.5 m above the floor in a place where there is good natural air
circulation. Don´t install the thermostat where the measuring can be
influenced by drafts, sunlight, heaters or any other effects. Avoid mounting
the thermostat on metal objects or metal bases which block radio
communication.
1. By pressing the tab (by screwdriver for instance) release the front part of
the thermostat.
2. Install the rear part of the thermostat at the choose place (tab down).
3. Insert the batteries; the polarity is marked on the plastic.
4. Put back the front thermostat part and close it.
Enrolling the thermostat
Install and connect the receiving unit to the heating appliance. If the
receiver has been bought independently, you have to enroll the thermostat to
it first. Open the enrollment mode on the receiver (see its manual) and insert
the batteries into the thermostat or press and hold the knob for 5s. In both
cases the thermostat will send an enrollment signal. The text
LRn
appears on
the LCD display when the enrolling procedure (with AC-116 only) has been
done successfully.
Symbols on the LCD:
Figure 2: 1 – Symbols of temperature and texts; 2 – Locking the thermostat;
3 – Alarm temperature-limits / Loss of communication; 4 – Heating ON / OFF;
5 – Low battery
Settings and programming
Do the complete settings using the knob – encoder. By pressing the knob 2
sec enter the programming mode.
General rules for programming:
1. Flashing of any icon on the LCD allows changing the option(s) or
choosing a next item.
2. Perform choosing or changing by turning the knob (turning the knob is
possible from left to right and vice versa).
3. Confirm the selection or change by briefly pressing the knob.
4. When the value of an item has been changed, then after this briefly press
the knob and the changes are saved. Then the thermostat goes to the
next item in the programming menu.
5. After the setting / change of the chosen items, select the parameter „OK“,
in the menu. By short pressing the system returns back to the previous
menu (up to the main menu).
6. If there is no manipulation of the knob for 30 sec, it returns you back to
the previous menu automatically.
The basic menu has 4 groups of settings.
LO
c
Locking the thermostat
OF
F
Switching off the thermostat
SE
t3
Service menu
OK
Saving the parameters and leaving the service menu
1. LOc – Locking the thermostat
To protect the thermostat against unwanted manipulation
you can lock the thermostat. Enter the menu and press
the knob on item
LOc
, the options
ON/OFF
appear. By
turning the knob select the requested state and confirm
by pressing. Choosing
ON
enables the function
Lock
, and blocks thermostat
control. To unlock the thermostat choose the option
OFF.
Locking the
thermostat is indicated on the LCD by the
symbol.
2. OFF – Switching off the thermostat
The thermostat can be switched off by the option
OFF
.
Enter the menu and press the knob on the item
OFF,
the options
ON/OFF
appear. By turning the knob select
the requested state and confirm by pressing. Choosing
ON
enables the function
OFF
, and switches off the thermostat. This is
indicated on the LCD by the text
OFF
. Although the thermostat has been
switched off, it still measures and detects the antifreeze temperature (see SE
t3, Stby). To unlock the thermostat enter the menu and choose the option
OFF
. When the knob is pressed the thermostat will be unlocked.
3. SEt3 – Service menu
The service parameters can be pre-programmed here. In a normal mode it is not
necessary to change those parameters. The Service menu includes 8 items. Open
by scrolling the knob to the requested item and by pressing the knob enter the
programming mode. Select the value again by scrolling the knob. Confirm it by
pressing the knob and it returns you back to the service menu.
HYst
is an item, where you can program the range of
the switching thresholds around the requested
temperature (hysteresis). The range can be set with a
0.1°C step from 0.1°C to 1°C. (Default setting
±
0.2°C)
Example:
With a set accuracy of ±0.
5˚C
a temperature of
24°C
will be kept this
way, at 23.
5°C it starts heating and at 24
.
5°C
it
stops heating.
In real conditions
regulation could have
a much bigger temperature scatter because of the thermal
inertia in
the
heated
premises.
Warning: An over-narrow pre-programmed hysteresis range could perform
on/off switching of the heating very often.
The item
Stby
sets the temperature which will be kept
in the case of switching off the thermostat (item
OFF
).
The
Stby
temperature is always at least 3°C higher
than
ALLo.
The value of the
Stby
temperature does
not have to be set higher than the
t Lo
temperature.
The
t Lo
item is the lower limit to which economical
temperate can be set.
The
t Hi
item is the upper limit to which the comfort
temperature can be set.
AL Lo
is the lower critical temperature. When the
temperature drops under the pre-set value, the
thermostat sends an alarm report to the receiver and
this state is indicated by a permanently lit (
!
) symbol.
The
ALLo
temperature is always at least 3°C lower
than
tLo
.
AL Hi
is the upper critical temperature. When the
temperature increases above the pre-set value, the
thermostat sends an alarm report to the receiver and
this state is indicated by a permanently lit (
!
) symbol.
The
ALHi
temperature is always at least 3°C higher
than
tHi.
For a reset to factory default settings the
RES
item is
used
.
After you enter the menu and press the knob on
the
RES
item
ON/OFF
appears. By scrolling the knob
select
ON,
and press the knob. Then a RESET will be
done.
When the reset is finished, a 20°C temperature
is pre-set.
By pressing the knob when the thermostat shows you
OK
you leave the service menu and return to the basic
thermostat menu.
TP-150 wireless indoor thermostat
1 / 2
MMC51601
TP-150 wireless indoor thermostat
The TP-150 is a wireless indoor thermostat. It serves for the measuring and
regulation of temperature. The temperature is set by the knob. The
thermostat regulates a pre-set temperature 24hrs per day.
The thermostat can be locked against unwanted manipulation. As well
as the regulation of temperature it can also report reaching the high and
low temperature limits.
Figure1
: 1 - knob (encoder) combined with button 2 - tab
Thermostat installation
The product can only be used in an indoor environment. Install the
thermostat 1.5 m above the floor in a place where there is good natural air
circulation. Don´t install the thermostat where the measuring can be
influenced by drafts, sunlight, heaters or any other effects. Avoid mounting
the thermostat on metal objects or metal bases which block radio
communication.
1. By pressing the tab (by screwdriver for instance) release the front part of
the thermostat.
2. Install the rear part of the thermostat at the choose place (tab down).
3. Insert the batteries; the polarity is marked on the plastic.
4. Put back the front thermostat part and close it.
Enrolling the thermostat
Install and connect the receiving unit to the heating appliance. If the
receiver has been bought independently, you have to enroll the thermostat to
it first. Open the enrollment mode on the receiver (see its manual) and insert
the batteries into the thermostat or press and hold the knob for 5s. In both
cases the thermostat will send an enrollment signal. The text
LRn
appears on
the LCD display when the enrolling procedure (with AC-116 only) has been
done successfully.
Symbols on the LCD:
Figure 2: 1 – Symbols of temperature and texts; 2 – Locking the thermostat;
3 – Alarm temperature-limits / Loss of communication; 4 – Heating ON / OFF;
5 – Low battery
Settings and programming
Do the complete settings using the knob – encoder. By pressing the knob 2
sec enter the programming mode.
General rules for programming:
1. Flashing of any icon on the LCD allows changing the option(s) or
choosing a next item.
2. Perform choosing or changing by turning the knob (turning the knob is
possible from left to right and vice versa).
3. Confirm the selection or change by briefly pressing the knob.
4. When the value of an item has been changed, then after this briefly press
the knob and the changes are saved. Then the thermostat goes to the
next item in the programming menu.
5. After the setting / change of the chosen items, select the parameter „OK“,
in the menu. By short pressing the system returns back to the previous
menu (up to the main menu).
6. If there is no manipulation of the knob for 30 sec, it returns you back to
the previous menu automatically.
The basic menu has 4 groups of settings.
LO
c
Locking the thermostat
OF
F
Switching off the thermostat
SE
t3
Service menu
OK
Saving the parameters and leaving the service menu
1. LOc – Locking the thermostat
To protect the thermostat against unwanted manipulation
you can lock the thermostat. Enter the menu and press
the knob on item
LOc
, the options
ON/OFF
appear. By
turning the knob select the requested state and confirm
by pressing. Choosing
ON
enables the function
Lock
, and blocks thermostat
control. To unlock the thermostat choose the option
OFF.
Locking the
thermostat is indicated on the LCD by the
symbol.
2. OFF – Switching off the thermostat
The thermostat can be switched off by the option
OFF
.
Enter the menu and press the knob on the item
OFF,
the options
ON/OFF
appear. By turning the knob select
the requested state and confirm by pressing. Choosing
ON
enables the function
OFF
, and switches off the thermostat. This is
indicated on the LCD by the text
OFF
. Although the thermostat has been
switched off, it still measures and detects the antifreeze temperature (see SE
t3, Stby). To unlock the thermostat enter the menu and choose the option
OFF
. When the knob is pressed the thermostat will be unlocked.
3. SEt3 – Service menu
The service parameters can be pre-programmed here. In a normal mode it is not
necessary to change those parameters. The Service menu includes 8 items. Open
by scrolling the knob to the requested item and by pressing the knob enter the
programming mode. Select the value again by scrolling the knob. Confirm it by
pressing the knob and it returns you back to the service menu.
HYst
is an item, where you can program the range of
the switching thresholds around the requested
temperature (hysteresis). The range can be set with a
0.1°C step from 0.1°C to 1°C. (Default setting
±
0.2°C)
Example:
With a set accuracy of ±0.
5˚C
a temperature of
24°C
will be kept this
way, at 23.
5°C it starts heating and at 24
.
5°C
it
stops heating.
In real conditions
regulation could have
a much bigger temperature scatter because of the thermal
inertia in
the
heated
premises.
Warning: An over-narrow pre-programmed hysteresis range could perform
on/off switching of the heating very often.
The item
Stby
sets the temperature which will be kept
in the case of switching off the thermostat (item
OFF
).
The
Stby
temperature is always at least 3°C higher
than
ALLo.
The value of the
Stby
temperature does
not have to be set higher than the
t Lo
temperature.
The
t Lo
item is the lower limit to which economical
temperate can be set.
The
t Hi
item is the upper limit to which the comfort
temperature can be set.
AL Lo
is the lower critical temperature. When the
temperature drops under the pre-set value, the
thermostat sends an alarm report to the receiver and
this state is indicated by a permanently lit (
!
) symbol.
The
ALLo
temperature is always at least 3°C lower
than
tLo
.
AL Hi
is the upper critical temperature. When the
temperature increases above the pre-set value, the
thermostat sends an alarm report to the receiver and
this state is indicated by a permanently lit (
!
) symbol.
The
ALHi
temperature is always at least 3°C higher
than
tHi.
For a reset to factory default settings the
RES
item is
used
.
After you enter the menu and press the knob on
the
RES
item
ON/OFF
appears. By scrolling the knob
select
ON,
and press the knob. Then a RESET will be
done.
When the reset is finished, a 20°C temperature
is pre-set.
By pressing the knob when the thermostat shows you
OK
you leave the service menu and return to the basic
thermostat menu.
TP-150 wireless indoor thermostat
1 / 2
MMC51601
TP-150 wireless indoor thermostat
The TP-150 is a wireless indoor thermostat. It serves for the measuring and
regulation of temperature. The temperature is set by the knob. The
thermostat regulates a pre-set temperature 24hrs per day.
The thermostat can be locked against unwanted manipulation. As well
as the regulation of temperature it can also report reaching the high and
low temperature limits.
Figure1
: 1 - knob (encoder) combined with button 2 - tab
Thermostat installation
The product can only be used in an indoor environment. Install the
thermostat 1.5 m above the floor in a place where there is good natural air
circulation. Don´t install the thermostat where the measuring can be
influenced by drafts, sunlight, heaters or any other effects. Avoid mounting
the thermostat on metal objects or metal bases which block radio
communication.
1. By pressing the tab (by screwdriver for instance) release the front part of
the thermostat.
2. Install the rear part of the thermostat at the choose place (tab down).
3. Insert the batteries; the polarity is marked on the plastic.
4. Put back the front thermostat part and close it.
Enrolling the thermostat
Install and connect the receiving unit to the heating appliance. If the
receiver has been bought independently, you have to enroll the thermostat to
it first. Open the enrollment mode on the receiver (see its manual) and insert
the batteries into the thermostat or press and hold the knob for 5s. In both
cases the thermostat will send an enrollment signal. The text
LRn
appears on
the LCD display when the enrolling procedure (with AC-116 only) has been
done successfully.
Symbols on the LCD:
Figure 2: 1 – Symbols of temperature and texts; 2 – Locking the thermostat;
3 – Alarm temperature-limits / Loss of communication; 4 – Heating ON / OFF;
5 – Low battery
Settings and programming
Do the complete settings using the knob – encoder. By pressing the knob 2
sec enter the programming mode.
General rules for programming:
1. Flashing of any icon on the LCD allows changing the option(s) or
choosing a next item.
2. Perform choosing or changing by turning the knob (turning the knob is
possible from left to right and vice versa).
3. Confirm the selection or change by briefly pressing the knob.
4. When the value of an item has been changed, then after this briefly press
the knob and the changes are saved. Then the thermostat goes to the
next item in the programming menu.
5. After the setting / change of the chosen items, select the parameter „OK“,
in the menu. By short pressing the system returns back to the previous
menu (up to the main menu).
6. If there is no manipulation of the knob for 30 sec, it returns you back to
the previous menu automatically.
The basic menu has 4 groups of settings.
LO
c
Locking the thermostat
OF
F
Switching off the thermostat
SE
t3
Service menu
OK
Saving the parameters and leaving the service menu
1. LOc – Locking the thermostat
To protect the thermostat against unwanted manipulation
you can lock the thermostat. Enter the menu and press
the knob on item
LOc
, the options
ON/OFF
appear. By
turning the knob select the requested state and confirm
by pressing. Choosing
ON
enables the function
Lock
, and blocks thermostat
control. To unlock the thermostat choose the option
OFF.
Locking the
thermostat is indicated on the LCD by the
symbol.
2. OFF – Switching off the thermostat
The thermostat can be switched off by the option
OFF
.
Enter the menu and press the knob on the item
OFF,
the options
ON/OFF
appear. By turning the knob select
the requested state and confirm by pressing. Choosing
ON
enables the function
OFF
, and switches off the thermostat. This is
indicated on the LCD by the text
OFF
. Although the thermostat has been
switched off, it still measures and detects the antifreeze temperature (see SE
t3, Stby). To unlock the thermostat enter the menu and choose the option
OFF
. When the knob is pressed the thermostat will be unlocked.
3. SEt3 – Service menu
The service parameters can be pre-programmed here. In a normal mode it is not
necessary to change those parameters. The Service menu includes 8 items. Open
by scrolling the knob to the requested item and by pressing the knob enter the
programming mode. Select the value again by scrolling the knob. Confirm it by
pressing the knob and it returns you back to the service menu.
HYst
is an item, where you can program the range of
the switching thresholds around the requested
temperature (hysteresis). The range can be set with a
0.1°C step from 0.1°C to 1°C. (Default setting
±
0.2°C)
Example:
With a set accuracy of ±0.
5˚C
a temperature of
24°C
will be kept this
way, at 23.
5°C it starts heating and at 24
.
5°C
it
stops heating.
In real conditions
regulation could have
a much bigger temperature scatter because of the thermal
inertia in
the
heated
premises.
Warning: An over-narrow pre-programmed hysteresis range could perform
on/off switching of the heating very often.
The item
Stby
sets the temperature which will be kept
in the case of switching off the thermostat (item
OFF
).
The
Stby
temperature is always at least 3°C higher
than
ALLo.
The value of the
Stby
temperature does
not have to be set higher than the
t Lo
temperature.
The
t Lo
item is the lower limit to which economical
temperate can be set.
The
t Hi
item is the upper limit to which the comfort
temperature can be set.
AL Lo
is the lower critical temperature. When the
temperature drops under the pre-set value, the
thermostat sends an alarm report to the receiver and
this state is indicated by a permanently lit (
!
) symbol.
The
ALLo
temperature is always at least 3°C lower
than
tLo
.
AL Hi
is the upper critical temperature. When the
temperature increases above the pre-set value, the
thermostat sends an alarm report to the receiver and
this state is indicated by a permanently lit (
!
) symbol.
The
ALHi
temperature is always at least 3°C higher
than
tHi.
For a reset to factory default settings the
RES
item is
used
.
After you enter the menu and press the knob on
the
RES
item
ON/OFF
appears. By scrolling the knob
select
ON,
and press the knob. Then a RESET will be
done.
When the reset is finished, a 20°C temperature
is pre-set.
By pressing the knob when the thermostat shows you
OK
you leave the service menu and return to the basic
thermostat menu.
TP-150 wireless indoor thermostat
1 / 2
MMC51601
TP-150 wireless indoor thermostat
The TP-150 is a wireless indoor thermostat. It serves for the measuring and
regulation of temperature. The temperature is set by the knob. The
thermostat regulates a pre-set temperature 24hrs per day.
The thermostat can be locked against unwanted manipulation. As well
as the regulation of temperature it can also report reaching the high and
low temperature limits.
Figure1
: 1 - knob (encoder) combined with button 2 - tab
Thermostat installation
The product can only be used in an indoor environment. Install the
thermostat 1.5 m above the floor in a place where there is good natural air
circulation. Don´t install the thermostat where the measuring can be
influenced by drafts, sunlight, heaters or any other effects. Avoid mounting
the thermostat on metal objects or metal bases which block radio
communication.
1. By pressing the tab (by screwdriver for instance) release the front part of
the thermostat.
2. Install the rear part of the thermostat at the choose place (tab down).
3. Insert the batteries; the polarity is marked on the plastic.
4. Put back the front thermostat part and close it.
Enrolling the thermostat
Install and connect the receiving unit to the heating appliance. If the
receiver has been bought independently, you have to enroll the thermostat to
it first. Open the enrollment mode on the receiver (see its manual) and insert
the batteries into the thermostat or press and hold the knob for 5s. In both
cases the thermostat will send an enrollment signal. The text
LRn
appears on
the LCD display when the enrolling procedure (with AC-116 only) has been
done successfully.
Symbols on the LCD:
Figure 2: 1 – Symbols of temperature and texts; 2 – Locking the thermostat;
3 – Alarm temperature-limits / Loss of communication; 4 – Heating ON / OFF;
5 – Low battery
Settings and programming
Do the complete settings using the knob – encoder. By pressing the knob 2
sec enter the programming mode.
General rules for programming:
1. Flashing of any icon on the LCD allows changing the option(s) or
choosing a next item.
2. Perform choosing or changing by turning the knob (turning the knob is
possible from left to right and vice versa).
3. Confirm the selection or change by briefly pressing the knob.
4. When the value of an item has been changed, then after this briefly press
the knob and the changes are saved. Then the thermostat goes to the
next item in the programming menu.
5. After the setting / change of the chosen items, select the parameter „OK“,
in the menu. By short pressing the system returns back to the previous
menu (up to the main menu).
6. If there is no manipulation of the knob for 30 sec, it returns you back to
the previous menu automatically.
The basic menu has 4 groups of settings.
LO
c
Locking the thermostat
OF
F
Switching off the thermostat
SE
t3
Service menu
OK
Saving the parameters and leaving the service menu
1. LOc – Locking the thermostat
To protect the thermostat against unwanted manipulation
you can lock the thermostat. Enter the menu and press
the knob on item
LOc
, the options
ON/OFF
appear. By
turning the knob select the requested state and confirm
by pressing. Choosing
ON
enables the function
Lock
, and blocks thermostat
control. To unlock the thermostat choose the option
OFF.
Locking the
thermostat is indicated on the LCD by the
symbol.
2. OFF – Switching off the thermostat
The thermostat can be switched off by the option
OFF
.
Enter the menu and press the knob on the item
OFF,
the options
ON/OFF
appear. By turning the knob select
the requested state and confirm by pressing. Choosing
ON
enables the function
OFF
, and switches off the thermostat. This is
indicated on the LCD by the text
OFF
. Although the thermostat has been
switched off, it still measures and detects the antifreeze temperature (see SE
t3, Stby). To unlock the thermostat enter the menu and choose the option
OFF
. When the knob is pressed the thermostat will be unlocked.
3. SEt3 – Service menu
The service parameters can be pre-programmed here. In a normal mode it is not
necessary to change those parameters. The Service menu includes 8 items. Open
by scrolling the knob to the requested item and by pressing the knob enter the
programming mode. Select the value again by scrolling the knob. Confirm it by
pressing the knob and it returns you back to the service menu.
HYst
is an item, where you can program the range of
the switching thresholds around the requested
temperature (hysteresis). The range can be set with a
0.1°C step from 0.1°C to 1°C. (Default setting
±
0.2°C)
Example:
With a set accuracy of ±0.
5˚C
a temperature of
24°C
will be kept this
way, at 23.
5°C it starts heating and at 24
.
5°C
it
stops heating.
In real conditions
regulation could have
a much bigger temperature scatter because of the thermal
inertia in
the
heated
premises.
Warning: An over-narrow pre-programmed hysteresis range could perform
on/off switching of the heating very often.
The item
Stby
sets the temperature which will be kept
in the case of switching off the thermostat (item
OFF
).
The
Stby
temperature is always at least 3°C higher
than
ALLo.
The value of the
Stby
temperature does
not have to be set higher than the
t Lo
temperature.
The
t Lo
item is the lower limit to which economical
temperate can be set.
The
t Hi
item is the upper limit to which the comfort
temperature can be set.
AL Lo
is the lower critical temperature. When the
temperature drops under the pre-set value, the
thermostat sends an alarm report to the receiver and
this state is indicated by a permanently lit (
!
) symbol.
The
ALLo
temperature is always at least 3°C lower
than
tLo
.
AL Hi
is the upper critical temperature. When the
temperature increases above the pre-set value, the
thermostat sends an alarm report to the receiver and
this state is indicated by a permanently lit (
!
) symbol.
The
ALHi
temperature is always at least 3°C higher
than
tHi.
For a reset to factory default settings the
RES
item is
used
.
After you enter the menu and press the knob on
the
RES
item
ON/OFF
appears. By scrolling the knob
select
ON,
and press the knob. Then a RESET will be
done.
When the reset is finished, a 20°C temperature
is pre-set.
By pressing the knob when the thermostat shows you
OK
you leave the service menu and return to the basic
thermostat menu.
TP-150 wireless indoor thermostat
1 / 2
MMC51601
This item allows to turn the adaptive pre-
heating On or Off according to the heating
system inertia. When auto modus is enabled,
the thermostat starts measuring the time
after which it has reached the requested
comfort temperature and according to this
time it starts the heating.
The reset function allows you to reset the
device to factory settings (listed in table). You
can perform reset by selecting Res in the
menu and pressing the knob and choosing
the menu Res.
By pressing the OK item you are leaving
the service menu and return to the basic
thermostat menu
Settings
item
Range
Factory
settings
Description
HYst
0.1°C to 1°C
0.2°C
Hysteresis
t Lo
+6°C to +40°C
6°C
lower limit of
temperature
t Hi
+6°C to +40°C
40°C
upper limit of
temperature
AL Lo
-9°C to +20°C
3°C
Panic Alarm
AL Hi
+30°C to +70°C
60°C
Fire alarm
+6°C to +40°C
18°C
Economical
temperature
+6°C to +40°C
21°C
Comfort
temperature
Party mode
In this mode it’s possible to raise or
decrease the temperature for an defined
amount of time. Party modus can only be
entered from the weekly programm. When
the defined time expires the thermostat will start again the weekly
schedule.
Party modus is entered when the display shows the ( )-symbol.
The first value is time (hours) after which the thermostat returns
to the weekly program. After time settings temperature settings
have to be done. The party mode is indicated by the ( )-symbol
on the display. If you want to leave teh party mode earlier than the
defined time, then the thermostat have to be set back to weekly
schedule.
Holiday mode
The holiday mode is designed to save costs
of the costumer. During vacation it is not
necessary to keep the temperature of the
weekly schedule. Like party modus, holiday mode is only possible
to enter from the weekly program.
If the holiday mode is entered the thermostat shows a flashing
value of days for which the economical temperature has to
be kept. The countdown starts from the moment of setting.
Substraction is done every day at midnight. When holiday mode
expires the thermostat returns to the weekly program.
Showing the pre-set temperature
The thermostat always shows the current room temperature in the
normal mode. Pressing the knob will show the temperature which
has been set for this time.
TP-150 wireless indoor thermostat
The TP-150 is a wireless indoor thermostat. It serves for the measuring and
regulation of temperature. The temperature is set by the knob. The
thermostat regulates a pre-set temperature 24hrs per day.
The thermostat can be locked against unwanted manipulation. As well
as the regulation of temperature it can also report reaching the high and
low temperature limits.
Figure1
: 1 - knob (encoder) combined with button 2 - tab
Thermostat installation
The product can only be used in an indoor environment. Install the
thermostat 1.5 m above the floor in a place where there is good natural air
circulation. Don´t install the thermostat where the measuring can be
influenced by drafts, sunlight, heaters or any other effects. Avoid mounting
the thermostat on metal objects or metal bases which block radio
communication.
1. By pressing the tab (by screwdriver for instance) release the front part of
the thermostat.
2. Install the rear part of the thermostat at the choose place (tab down).
3. Insert the batteries; the polarity is marked on the plastic.
4. Put back the front thermostat part and close it.
Enrolling the thermostat
Install and connect the receiving unit to the heating appliance. If the
receiver has been bought independently, you have to enroll the thermostat to
it first. Open the enrollment mode on the receiver (see its manual) and insert
the batteries into the thermostat or press and hold the knob for 5s. In both
cases the thermostat will send an enrollment signal. The text
LRn
appears on
the LCD display when the enrolling procedure (with AC-116 only) has been
done successfully.
Symbols on the LCD:
Figure 2: 1 – Symbols of temperature and texts; 2 – Locking the thermostat;
3 – Alarm temperature-limits / Loss of communication; 4 – Heating ON / OFF;
5 – Low battery
Settings and programming
Do the complete settings using the knob – encoder. By pressing the knob 2
sec enter the programming mode.
General rules for programming:
1. Flashing of any icon on the LCD allows changing the option(s) or
choosing a next item.
2. Perform choosing or changing by turning the knob (turning the knob is
possible from left to right and vice versa).
3. Confirm the selection or change by briefly pressing the knob.
4. When the value of an item has been changed, then after this briefly press
the knob and the changes are saved. Then the thermostat goes to the
next item in the programming menu.
5. After the setting / change of the chosen items, select the parameter „OK“,
in the menu. By short pressing the system returns back to the previous
menu (up to the main menu).
6. If there is no manipulation of the knob for 30 sec, it returns you back to
the previous menu automatically.
The basic menu has 4 groups of settings.
LO
c
Locking the thermostat
OF
F
Switching off the thermostat
SE
t3
Service menu
OK
Saving the parameters and leaving the service menu
1. LOc – Locking the thermostat
To protect the thermostat against unwanted manipulation
you can lock the thermostat. Enter the menu and press
the knob on item
LOc
, the options
ON/OFF
appear. By
turning the knob select the requested state and confirm
by pressing. Choosing
ON
enables the function
Lock
, and blocks thermostat
control. To unlock the thermostat choose the option
OFF.
Locking the
thermostat is indicated on the LCD by the
symbol.
2. OFF – Switching off the thermostat
The thermostat can be switched off by the option
OFF
.
Enter the menu and press the knob on the item
OFF,
the options
ON/OFF
appear. By turning the knob select
the requested state and confirm by pressing. Choosing
ON
enables the function
OFF
, and switches off the thermostat. This is
indicated on the LCD by the text
OFF
. Although the thermostat has been
switched off, it still measures and detects the antifreeze temperature (see SE
t3, Stby). To unlock the thermostat enter the menu and choose the option
OFF
. When the knob is pressed the thermostat will be unlocked.
3. SEt3 – Service menu
The service parameters can be pre-programmed here. In a normal mode it is not
necessary to change those parameters. The Service menu includes 8 items. Open
by scrolling the knob to the requested item and by pressing the knob enter the
programming mode. Select the value again by scrolling the knob. Confirm it by
pressing the knob and it returns you back to the service menu.
HYst
is an item, where you can program the range of
the switching thresholds around the requested
temperature (hysteresis). The range can be set with a
0.1°C step from 0.1°C to 1°C. (Default setting
±
0.2°C)
Example:
With a set accuracy of ±0.
5˚C
a temperature of
24°C
will be kept this
way, at 23.
5°C it starts heating and at 24
.
5°C
it
stops heating.
In real conditions
regulation could have
a much bigger temperature scatter because of the thermal
inertia in
the
heated
premises.
Warning: An over-narrow pre-programmed hysteresis range could perform
on/off switching of the heating very often.
The item
Stby
sets the temperature which will be kept
in the case of switching off the thermostat (item
OFF
).
The
Stby
temperature is always at least 3°C higher
than
ALLo.
The value of the
Stby
temperature does
not have to be set higher than the
t Lo
temperature.
The
t Lo
item is the lower limit to which economical
temperate can be set.
The
t Hi
item is the upper limit to which the comfort
temperature can be set.
AL Lo
is the lower critical temperature. When the
temperature drops under the pre-set value, the
thermostat sends an alarm report to the receiver and
this state is indicated by a permanently lit (
!
) symbol.
The
ALLo
temperature is always at least 3°C lower
than
tLo
.
AL Hi
is the upper critical temperature. When the
temperature increases above the pre-set value, the
thermostat sends an alarm report to the receiver and
this state is indicated by a permanently lit (
!
) symbol.
The
ALHi
temperature is always at least 3°C higher
than
tHi.
For a reset to factory default settings the
RES
item is
used
.
After you enter the menu and press the knob on
the
RES
item
ON/OFF
appears. By scrolling the knob
select
ON,
and press the knob. Then a RESET will be
done.
When the reset is finished, a 20°C temperature
is pre-set.
By pressing the knob when the thermostat shows you
OK
you leave the service menu and return to the basic
thermostat menu.
TP-150 wireless indoor thermostat
1 / 2
MMC51601
TP-150 wireless indoor thermostat
The TP-150 is a wireless indoor thermostat. It serves for the measuring and
regulation of temperature. The temperature is set by the knob. The
thermostat regulates a pre-set temperature 24hrs per day.
The thermostat can be locked against unwanted manipulation. As well
as the regulation of temperature it can also report reaching the high and
low temperature limits.
Figure1
: 1 - knob (encoder) combined with button 2 - tab
Thermostat installation
The product can only be used in an indoor environment. Install the
thermostat 1.5 m above the floor in a place where there is good natural air
circulation. Don´t install the thermostat where the measuring can be
influenced by drafts, sunlight, heaters or any other effects. Avoid mounting
the thermostat on metal objects or metal bases which block radio
communication.
1. By pressing the tab (by screwdriver for instance) release the front part of
the thermostat.
2. Install the rear part of the thermostat at the choose place (tab down).
3. Insert the batteries; the polarity is marked on the plastic.
4. Put back the front thermostat part and close it.
Enrolling the thermostat
Install and connect the receiving unit to the heating appliance. If the
receiver has been bought independently, you have to enroll the thermostat to
it first. Open the enrollment mode on the receiver (see its manual) and insert
the batteries into the thermostat or press and hold the knob for 5s. In both
cases the thermostat will send an enrollment signal. The text
LRn
appears on
the LCD display when the enrolling procedure (with AC-116 only) has been
done successfully.
Symbols on the LCD:
Figure 2: 1 – Symbols of temperature and texts; 2 – Locking the thermostat;
3 – Alarm temperature-limits / Loss of communication; 4 – Heating ON / OFF;
5 – Low battery
Settings and programming
Do the complete settings using the knob – encoder. By pressing the knob 2
sec enter the programming mode.
General rules for programming:
1. Flashing of any icon on the LCD allows changing the option(s) or
choosing a next item.
2. Perform choosing or changing by turning the knob (turning the knob is
possible from left to right and vice versa).
3. Confirm the selection or change by briefly pressing the knob.
4. When the value of an item has been changed, then after this briefly press
the knob and the changes are saved. Then the thermostat goes to the
next item in the programming menu.
5. After the setting / change of the chosen items, select the parameter „OK“,
in the menu. By short pressing the system returns back to the previous
menu (up to the main menu).
6. If there is no manipulation of the knob for 30 sec, it returns you back to
the previous menu automatically.
The basic menu has 4 groups of settings.
LO
c
Locking the thermostat
OF
F
Switching off the thermostat
SE
t3
Service menu
OK
Saving the parameters and leaving the service menu
1. LOc – Locking the thermostat
To protect the thermostat against unwanted manipulation
you can lock the thermostat. Enter the menu and press
the knob on item
LOc
, the options
ON/OFF
appear. By
turning the knob select the requested state and confirm
by pressing. Choosing
ON
enables the function
Lock
, and blocks thermostat
control. To unlock the thermostat choose the option
OFF.
Locking the
thermostat is indicated on the LCD by the
symbol.
2. OFF – Switching off the thermostat
The thermostat can be switched off by the option
OFF
.
Enter the menu and press the knob on the item
OFF,
the options
ON/OFF
appear. By turning the knob select
the requested state and confirm by pressing. Choosing
ON
enables the function
OFF
, and switches off the thermostat. This is
indicated on the LCD by the text
OFF
. Although the thermostat has been
switched off, it still measures and detects the antifreeze temperature (see SE
t3, Stby). To unlock the thermostat enter the menu and choose the option
OFF
. When the knob is pressed the thermostat will be unlocked.
3. SEt3 – Service menu
The service parameters can be pre-programmed here. In a normal mode it is not
necessary to change those parameters. The Service menu includes 8 items. Open
by scrolling the knob to the requested item and by pressing the knob enter the
programming mode. Select the value again by scrolling the knob. Confirm it by
pressing the knob and it returns you back to the service menu.
HYst
is an item, where you can program the range of
the switching thresholds around the requested
temperature (hysteresis). The range can be set with a
0.1°C step from 0.1°C to 1°C. (Default setting
±
0.2°C)
Example:
With a set accuracy of ±0.
5˚C
a temperature of
24°C
will be kept this
way, at 23.
5°C it starts heating and at 24
.
5°C
it
stops heating.
In real conditions
regulation could have
a much bigger temperature scatter because of the thermal
inertia in
the
heated
premises.
Warning: An over-narrow pre-programmed hysteresis range could perform
on/off switching of the heating very often.
The item
Stby
sets the temperature which will be kept
in the case of switching off the thermostat (item
OFF
).
The
Stby
temperature is always at least 3°C higher
than
ALLo.
The value of the
Stby
temperature does
not have to be set higher than the
t Lo
temperature.
The
t Lo
item is the lower limit to which economical
temperate can be set.
The
t Hi
item is the upper limit to which the comfort
temperature can be set.
AL Lo
is the lower critical temperature. When the
temperature drops under the pre-set value, the
thermostat sends an alarm report to the receiver and
this state is indicated by a permanently lit (
!
) symbol.
The
ALLo
temperature is always at least 3°C lower
than
tLo
.
AL Hi
is the upper critical temperature. When the
temperature increases above the pre-set value, the
thermostat sends an alarm report to the receiver and
this state is indicated by a permanently lit (
!
) symbol.
The
ALHi
temperature is always at least 3°C higher
than
tHi.
For a reset to factory default settings the
RES
item is
used
.
After you enter the menu and press the knob on
the
RES
item
ON/OFF
appears. By scrolling the knob
select
ON,
and press the knob. Then a RESET will be
done.
When the reset is finished, a 20°C temperature
is pre-set.
By pressing the knob when the thermostat shows you
OK
you leave the service menu and return to the basic
thermostat menu.
TP-150 wireless indoor thermostat
1 / 2
MMC51601
TP-155 Wireless programmable indoor thermostat
The TP-155 is a wireless programmable indoor thermostat with a weekly heating
schedule. It can regulate the
economical or comfort temperature
inside residential buildings. It offers a
few programmable modes. Every
mode regulates pre-set temperatures
(Comfort, Economy, Holiday, and
Party). The thermostat is able to
measure the thermal inertia inside the
premises and adjust the weekly
schedule
for the requested
temperature to be reached at the pre-
set time.
Figure 1
: 1- knob (encoder) combined with button; 2- tab
Thermostat installation
The product can only be used in an indoor environment. Install the thermostat 1.5
m above the floor in a place where there is good natural air circulation. Don´t install
the thermostat where the measuring can be influenced by drafts, sunlight, heaters or
any other effects. Avoid mounting the thermostat on metal objects or metal bases
which block radio communication.
1. By pressing the tab (by screwdriver for instance) release the front part of the
thermostat.
2. Install the rear part of the thermostat at the chosen place (tab down).
3. Insert the batteries, the polarity is marked on the plastic.
4. Put back the front thermostat part and close it.
Enrolling the thermostat
Install and connect the receiving unit to the heating appliance. If the receiver has
been bought independently, you have to enroll the thermostat to it first. Open the
enrollment mode on the receiver (see its manual) and insert the batteries into the
thermostat or press and hold the knob for 5s. In both cases the thermostat will send
an enrollment signal. The text
LRn
appears on the LCD display when the enrolling
procedure (with AC-116 only) has been done successfully.
Symbols on the LCD:
Figure 2: 1 – Symbols for
comfort and economical
temperatures; 2 – The days of
the week; 3 – Locking the
thermostat; 4 – Alarm tempe-
rature
–
limits / loss of
communication; 5 – Heating
ON / OFF; 6 – Holiday; 7 – Party;
8 – Heating times; 9 – Symbols
for showing temperature time
and texts; 10 – Low battery
Settings and programming
Do the complete settings using the knob – encoder. By pressing the knob 2 sec
enter the programming mode.
General rules for programming:
1. Flashing of any icon on the LCD allows changing the option(s) or choosing a
next item.
2. Perform choosing or changing by turning the knob (turning the knob is possible
from left to right and vice versa).
3. Confirm the selection or change by briefly pressing the knob.
4. When the value of an item has been changed, then after this briefly press the
knob and the changes are saved. Then the thermostat goes to the next item in
the programming menu.
5. After the setting / change of the chosen items, select the parameter „OK“, in the
menu. By short pressing the system returns back to the previous menu (up to
the main menu).
6. If there is no manipulation of the knob for 30 sec, it returns you back to the
previous menu automatically.
The basic menu has 7 groups of settings.
MA
n
Manual mode
LO
c
Locking the thermostat
OF
F
Switching off the thermostat
SE
t1
Temperature, date and time settings
SE
t2
Weekly schedule setting
SE
t3
Service menu
OK
Saving the parameters and leaving the service menu
1. MAn – manual mode
The temperature is set manually regardless of the weekly
schedule and is kept. Enter the menu and press the knob on
the item
Man,
the option ON (switched on) appears. By
turning the knob select the requested state and confirm by
pressing. The temperatures
tLo
and
tHi
determine the regulation range pre-
programmed in the service menu SE t3, in which you can select the temperature by
turning the knob. Choose the requested temperature. If the chosen temperature is
lower than the required temperature, the thermostat shows the symbol
(▲)
on its
LCD display. By entering the menu
Man
and confirming the option
OFF
, manual
mode is terminated.
2. LOc – Locking the thermostat
To protect the thermostat against unwanted manipulation you
can lock the thermostat. Enter the menu and press the knob
on the item
LOc,
the options
ON/OFF
appear. By turning the
knob select the requested state and confirm by pressing.
Choosing
ON
enables the function
Lock
, and blocks thermostat control. To unlock
the thermostat choose the option
OFF.
Locking the thermostat is indicated on the
LCD by the
symbol.
3. OFF – Switching off the thermostat
The thermostat can be switched off by the option
OFF
.
Enter the menu and press the knob on the item
OFF,
the
options
ON/OFF
appear. By turning the knob select the
requested state and confirm by pressing. Choosing
ON
enables the function
OFF
, and switches off the thermostat. This is indicated on the
LCD by the text
OFF
. Although the thermostat has been switched off, it still
measures and detects the antifreeze temperature (see SE t3, Stby). To unlock the
thermostat enter the menu and choose the option
OFF.
When the knob is pressed
the thermostat will be unlocked.
4. Set1 - Temperature, date and time settings
In the Set1 menu the comfort temperature ( ), the economy
temperature ( ), the temperature for Holiday mode ( ), and
the data and time can be preset. Enter the menu
Set1
, and
on the LCD the symbol of the economy temperature starts
flashing. By turning the knob select the requested item ( , or ), by pressing the
knob the symbols for temperature start flashing and again by turning the knob set the
required temperature and by repeatedly pressing the knob confirm this setting. The
last item serves for setting the current time. It indicates using flashing symbols of the
days of the week. By pressing you enter the current time setting. It starts with the
year. Pressing gets it flashing, and by turning the knob set the year, by pressing
again it saves the setting and then you continue the same way in setting the current
month, day, hour and minute. Then by pressing the knob after the minute setting the
values are saved and the thermostat is back in the menu
Set1
. Select the item
OK
to
leave this menu.
5. SEt2 – Weekly schedule setting
The heating program for switching the comfort and the economy temperatures can
be set for every single day independently (Mo - Monday, Tu - Tuesday, We -
Wednesday, Th - Thursday, Fr - Friday, Sa - Saturday, Su - Sunday) or it can be
split into working days and the weekend. There is one more option - the same
settings for all days with no difference.
Enter the menu
Set2
, and by turning the knob select the combination of days which
is required. Confirm by briefly pressing the knob. It enters the programming of heating
time periods when the thermostat switches between the day temperature and the
night temperature.
Programming always starts at 00 hrs. By turning the knob
clockwise, you can move through the time line. Press the
knob at the point from which you want to start with the
heating to the comfort temperature. The symbol changes
to the . Now by turning the knob clockwise the points
appear which represent the hours for which heating is
performed to the economy temperature. By turning the
knob anti-clockwise the points are erased. Pressing the
knob more switches the economy temperature to the
comfort temperature. By repeating this procedure the
comfort and economy temperatures can be set for a
selected day (or for a group of a few days). After the
programming of the whole day has been finished, the
thermostat shows you
OK
. When the knob is pressed, all
settings are saved.
6. SEt3 – Service menu
The service parameters can be pre-programmed here. In normal mode it is not
necessary to change those parameters. The Service menu includes 9 items. Open
by scrolling the knob to the requested item and by pressing the knob to enter the
programming mode. Select the value again by scrolling the knob. Confirm it by
pressing the knob and it returns you back to the service menu.
TP-155 Wireless programmable indoor thermostat
1 / 2
MMC51701
TP-155 Wireless programmable indoor thermostat
The TP-155 is a wireless programmable indoor thermostat with a weekly heating
schedule. It can regulate the
economical or comfort temperature
inside residential buildings. It offers a
few programmable modes. Every
mode regulates pre-set temperatures
(Comfort, Economy, Holiday, and
Party). The thermostat is able to
measure the thermal inertia inside the
premises and adjust the weekly
schedule
for the requested
temperature to be reached at the pre-
set time.
Figure 1
: 1- knob (encoder) combined with button; 2- tab
Thermostat installation
The product can only be used in an indoor environment. Install the thermostat 1.5
m above the floor in a place where there is good natural air circulation. Don´t install
the thermostat where the measuring can be influenced by drafts, sunlight, heaters or
any other effects. Avoid mounting the thermostat on metal objects or metal bases
which block radio communication.
1. By pressing the tab (by screwdriver for instance) release the front part of the
thermostat.
2. Install the rear part of the thermostat at the chosen place (tab down).
3. Insert the batteries, the polarity is marked on the plastic.
4. Put back the front thermostat part and close it.
Enrolling the thermostat
Install and connect the receiving unit to the heating appliance. If the receiver has
been bought independently, you have to enroll the thermostat to it first. Open the
enrollment mode on the receiver (see its manual) and insert the batteries into the
thermostat or press and hold the knob for 5s. In both cases the thermostat will send
an enrollment signal. The text
LRn
appears on the LCD display when the enrolling
procedure (with AC-116 only) has been done successfully.
Symbols on the LCD:
Figure 2: 1 – Symbols for
comfort and economical
temperatures; 2 – The days of
the week; 3 – Locking the
thermostat; 4 – Alarm tempe-
rature
–
limits / loss of
communication; 5 – Heating
ON / OFF; 6 – Holiday; 7 – Party;
8 – Heating times; 9 – Symbols
for showing temperature time
and texts; 10 – Low battery
Settings and programming
Do the complete settings using the knob – encoder. By pressing the knob 2 sec
enter the programming mode.
General rules for programming:
1. Flashing of any icon on the LCD allows changing the option(s) or choosing a
next item.
2. Perform choosing or changing by turning the knob (turning the knob is possible
from left to right and vice versa).
3. Confirm the selection or change by briefly pressing the knob.
4. When the value of an item has been changed, then after this briefly press the
knob and the changes are saved. Then the thermostat goes to the next item in
the programming menu.
5. After the setting / change of the chosen items, select the parameter „OK“, in the
menu. By short pressing the system returns back to the previous menu (up to
the main menu).
6. If there is no manipulation of the knob for 30 sec, it returns you back to the
previous menu automatically.
The basic menu has 7 groups of settings.
MA
n
Manual mode
LO
c
Locking the thermostat
OF
F
Switching off the thermostat
SE
t1
Temperature, date and time settings
SE
t2
Weekly schedule setting
SE
t3
Service menu
OK
Saving the parameters and leaving the service menu
1. MAn – manual mode
The temperature is set manually regardless of the weekly
schedule and is kept. Enter the menu and press the knob on
the item
Man,
the option ON (switched on) appears. By
turning the knob select the requested state and confirm by
pressing. The temperatures
tLo
and
tHi
determine the regulation range pre-
programmed in the service menu SE t3, in which you can select the temperature by
turning the knob. Choose the requested temperature. If the chosen temperature is
lower than the required temperature, the thermostat shows the symbol
(▲)
on its
LCD display. By entering the menu
Man
and confirming the option
OFF
, manual
mode is terminated.
2. LOc – Locking the thermostat
To protect the thermostat against unwanted manipulation you
can lock the thermostat. Enter the menu and press the knob
on the item
LOc,
the options
ON/OFF
appear. By turning the
knob select the requested state and confirm by pressing.
Choosing
ON
enables the function
Lock
, and blocks thermostat control. To unlock
the thermostat choose the option
OFF.
Locking the thermostat is indicated on the
LCD by the
symbol.
3. OFF – Switching off the thermostat
The thermostat can be switched off by the option
OFF
.
Enter the menu and press the knob on the item
OFF,
the
options
ON/OFF
appear. By turning the knob select the
requested state and confirm by pressing. Choosing
ON
enables the function
OFF
, and switches off the thermostat. This is indicated on the
LCD by the text
OFF
. Although the thermostat has been switched off, it still
measures and detects the antifreeze temperature (see SE t3, Stby). To unlock the
thermostat enter the menu and choose the option
OFF.
When the knob is pressed
the thermostat will be unlocked.
4. Set1 - Temperature, date and time settings
In the Set1 menu the comfort temperature ( ), the economy
temperature ( ), the temperature for Holiday mode ( ), and
the data and time can be preset. Enter the menu
Set1
, and
on the LCD the symbol of the economy temperature starts
flashing. By turning the knob select the requested item ( , or ), by pressing the
knob the symbols for temperature start flashing and again by turning the knob set the
required temperature and by repeatedly pressing the knob confirm this setting. The
last item serves for setting the current time. It indicates using flashing symbols of the
days of the week. By pressing you enter the current time setting. It starts with the
year. Pressing gets it flashing, and by turning the knob set the year, by pressing
again it saves the setting and then you continue the same way in setting the current
month, day, hour and minute. Then by pressing the knob after the minute setting the
values are saved and the thermostat is back in the menu
Set1
. Select the item
OK
to
leave this menu.
5. SEt2 – Weekly schedule setting
The heating program for switching the comfort and the economy temperatures can
be set for every single day independently (Mo - Monday, Tu - Tuesday, We -
Wednesday, Th - Thursday, Fr - Friday, Sa - Saturday, Su - Sunday) or it can be
split into working days and the weekend. There is one more option - the same
settings for all days with no difference.
Enter the menu
Set2
, and by turning the knob select the combination of days which
is required. Confirm by briefly pressing the knob. It enters the programming of heating
time periods when the thermostat switches between the day temperature and the
night temperature.
Programming always starts at 00 hrs. By turning the knob
clockwise, you can move through the time line. Press the
knob at the point from which you want to start with the
heating to the comfort temperature. The symbol changes
to the . Now by turning the knob clockwise the points
appear which represent the hours for which heating is
performed to the economy temperature. By turning the
knob anti-clockwise the points are erased. Pressing the
knob more switches the economy temperature to the
comfort temperature. By repeating this procedure the
comfort and economy temperatures can be set for a
selected day (or for a group of a few days). After the
programming of the whole day has been finished, the
thermostat shows you
OK
. When the knob is pressed, all
settings are saved.
6. SEt3 – Service menu
The service parameters can be pre-programmed here. In normal mode it is not
necessary to change those parameters. The Service menu includes 9 items. Open
by scrolling the knob to the requested item and by pressing the knob to enter the
programming mode. Select the value again by scrolling the knob. Confirm it by
pressing the knob and it returns you back to the service menu.
TP-155 Wireless programmable indoor thermostat
1 / 2
MMC51701
TP-155 Wireless programmable indoor thermostat
The TP-155 is a wireless programmable indoor thermostat with a weekly heating
schedule. It can regulate the
economical or comfort temperature
inside residential buildings. It offers a
few programmable modes. Every
mode regulates pre-set temperatures
(Comfort, Economy, Holiday, and
Party). The thermostat is able to
measure the thermal inertia inside the
premises and adjust the weekly
schedule
for the requested
temperature to be reached at the pre-
set time.
Figure 1
: 1- knob (encoder) combined with button; 2- tab
Thermostat installation
The product can only be used in an indoor environment. Install the thermostat 1.5
m above the floor in a place where there is good natural air circulation. Don´t install
the thermostat where the measuring can be influenced by drafts, sunlight, heaters or
any other effects. Avoid mounting the thermostat on metal objects or metal bases
which block radio communication.
1. By pressing the tab (by screwdriver for instance) release the front part of the
thermostat.
2. Install the rear part of the thermostat at the chosen place (tab down).
3. Insert the batteries, the polarity is marked on the plastic.
4. Put back the front thermostat part and close it.
Enrolling the thermostat
Install and connect the receiving unit to the heating appliance. If the receiver has
been bought independently, you have to enroll the thermostat to it first. Open the
enrollment mode on the receiver (see its manual) and insert the batteries into the
thermostat or press and hold the knob for 5s. In both cases the thermostat will send
an enrollment signal. The text
LRn
appears on the LCD display when the enrolling
procedure (with AC-116 only) has been done successfully.
Symbols on the LCD:
Figure 2: 1 – Symbols for
comfort and economical
temperatures; 2 – The days of
the week; 3 – Locking the
thermostat; 4 – Alarm tempe-
rature
–
limits / loss of
communication; 5 – Heating
ON / OFF; 6 – Holiday; 7 – Party;
8 – Heating times; 9 – Symbols
for showing temperature time
and texts; 10 – Low battery
Settings and programming
Do the complete settings using the knob – encoder. By pressing the knob 2 sec
enter the programming mode.
General rules for programming:
1. Flashing of any icon on the LCD allows changing the option(s) or choosing a
next item.
2. Perform choosing or changing by turning the knob (turning the knob is possible
from left to right and vice versa).
3. Confirm the selection or change by briefly pressing the knob.
4. When the value of an item has been changed, then after this briefly press the
knob and the changes are saved. Then the thermostat goes to the next item in
the programming menu.
5. After the setting / change of the chosen items, select the parameter „OK“, in the
menu. By short pressing the system returns back to the previous menu (up to
the main menu).
6. If there is no manipulation of the knob for 30 sec, it returns you back to the
previous menu automatically.
The basic menu has 7 groups of settings.
MA
n
Manual mode
LO
c
Locking the thermostat
OF
F
Switching off the thermostat
SE
t1
Temperature, date and time settings
SE
t2
Weekly schedule setting
SE
t3
Service menu
OK
Saving the parameters and leaving the service menu
1. MAn – manual mode
The temperature is set manually regardless of the weekly
schedule and is kept. Enter the menu and press the knob on
the item
Man,
the option ON (switched on) appears. By
turning the knob select the requested state and confirm by
pressing. The temperatures
tLo
and
tHi
determine the regulation range pre-
programmed in the service menu SE t3, in which you can select the temperature by
turning the knob. Choose the requested temperature. If the chosen temperature is
lower than the required temperature, the thermostat shows the symbol
(▲)
on its
LCD display. By entering the menu
Man
and confirming the option
OFF
, manual
mode is terminated.
2. LOc – Locking the thermostat
To protect the thermostat against unwanted manipulation you
can lock the thermostat. Enter the menu and press the knob
on the item
LOc,
the options
ON/OFF
appear. By turning the
knob select the requested state and confirm by pressing.
Choosing
ON
enables the function
Lock
, and blocks thermostat control. To unlock
the thermostat choose the option
OFF.
Locking the thermostat is indicated on the
LCD by the
symbol.
3. OFF – Switching off the thermostat
The thermostat can be switched off by the option
OFF
.
Enter the menu and press the knob on the item
OFF,
the
options
ON/OFF
appear. By turning the knob select the
requested state and confirm by pressing. Choosing
ON
enables the function
OFF
, and switches off the thermostat. This is indicated on the
LCD by the text
OFF
. Although the thermostat has been switched off, it still
measures and detects the antifreeze temperature (see SE t3, Stby). To unlock the
thermostat enter the menu and choose the option
OFF.
When the knob is pressed
the thermostat will be unlocked.
4. Set1 - Temperature, date and time settings
In the Set1 menu the comfort temperature ( ), the economy
temperature ( ), the temperature for Holiday mode ( ), and
the data and time can be preset. Enter the menu
Set1
, and
on the LCD the symbol of the economy temperature starts
flashing. By turning the knob select the requested item ( , or ), by pressing the
knob the symbols for temperature start flashing and again by turning the knob set the
required temperature and by repeatedly pressing the knob confirm this setting. The
last item serves for setting the current time. It indicates using flashing symbols of the
days of the week. By pressing you enter the current time setting. It starts with the
year. Pressing gets it flashing, and by turning the knob set the year, by pressing
again it saves the setting and then you continue the same way in setting the current
month, day, hour and minute. Then by pressing the knob after the minute setting the
values are saved and the thermostat is back in the menu
Set1
. Select the item
OK
to
leave this menu.
5. SEt2 – Weekly schedule setting
The heating program for switching the comfort and the economy temperatures can
be set for every single day independently (Mo - Monday, Tu - Tuesday, We -
Wednesday, Th - Thursday, Fr - Friday, Sa - Saturday, Su - Sunday) or it can be
split into working days and the weekend. There is one more option - the same
settings for all days with no difference.
Enter the menu
Set2
, and by turning the knob select the combination of days which
is required. Confirm by briefly pressing the knob. It enters the programming of heating
time periods when the thermostat switches between the day temperature and the
night temperature.
Programming always starts at 00 hrs. By turning the knob
clockwise, you can move through the time line. Press the
knob at the point from which you want to start with the
heating to the comfort temperature. The symbol changes
to the . Now by turning the knob clockwise the points
appear which represent the hours for which heating is
performed to the economy temperature. By turning the
knob anti-clockwise the points are erased. Pressing the
knob more switches the economy temperature to the
comfort temperature. By repeating this procedure the
comfort and economy temperatures can be set for a
selected day (or for a group of a few days). After the
programming of the whole day has been finished, the
thermostat shows you
OK
. When the knob is pressed, all
settings are saved.
6. SEt3 – Service menu
The service parameters can be pre-programmed here. In normal mode it is not
necessary to change those parameters. The Service menu includes 9 items. Open
by scrolling the knob to the requested item and by pressing the knob to enter the
programming mode. Select the value again by scrolling the knob. Confirm it by
pressing the knob and it returns you back to the service menu.
TP-155 Wireless programmable indoor thermostat
1 / 2
MMC51701
TP-155 Wireless programmable indoor thermostat
The TP-155 is a wireless programmable indoor thermostat with a weekly heating
schedule. It can regulate the
economical or comfort temperature
inside residential buildings. It offers a
few programmable modes. Every
mode regulates pre-set temperatures
(Comfort, Economy, Holiday, and
Party). The thermostat is able to
measure the thermal inertia inside the
premises and adjust the weekly
schedule
for the requested
temperature to be reached at the pre-
set time.
Figure 1
: 1- knob (encoder) combined with button; 2- tab
Thermostat installation
The product can only be used in an indoor environment. Install the thermostat 1.5
m above the floor in a place where there is good natural air circulation. Don´t install
the thermostat where the measuring can be influenced by drafts, sunlight, heaters or
any other effects. Avoid mounting the thermostat on metal objects or metal bases
which block radio communication.
1. By pressing the tab (by screwdriver for instance) release the front part of the
thermostat.
2. Install the rear part of the thermostat at the chosen place (tab down).
3. Insert the batteries, the polarity is marked on the plastic.
4. Put back the front thermostat part and close it.
Enrolling the thermostat
Install and connect the receiving unit to the heating appliance. If the receiver has
been bought independently, you have to enroll the thermostat to it first. Open the
enrollment mode on the receiver (see its manual) and insert the batteries into the
thermostat or press and hold the knob for 5s. In both cases the thermostat will send
an enrollment signal. The text
LRn
appears on the LCD display when the enrolling
procedure (with AC-116 only) has been done successfully.
Symbols on the LCD:
Figure 2: 1 – Symbols for
comfort and economical
temperatures; 2 – The days of
the week; 3 – Locking the
thermostat; 4 – Alarm tempe-
rature
–
limits / loss of
communication; 5 – Heating
ON / OFF; 6 – Holiday; 7 – Party;
8 – Heating times; 9 – Symbols
for showing temperature time
and texts; 10 – Low battery
Settings and programming
Do the complete settings using the knob – encoder. By pressing the knob 2 sec
enter the programming mode.
General rules for programming:
1. Flashing of any icon on the LCD allows changing the option(s) or choosing a
next item.
2. Perform choosing or changing by turning the knob (turning the knob is possible
from left to right and vice versa).
3. Confirm the selection or change by briefly pressing the knob.
4. When the value of an item has been changed, then after this briefly press the
knob and the changes are saved. Then the thermostat goes to the next item in
the programming menu.
5. After the setting / change of the chosen items, select the parameter „OK“, in the
menu. By short pressing the system returns back to the previous menu (up to
the main menu).
6. If there is no manipulation of the knob for 30 sec, it returns you back to the
previous menu automatically.
The basic menu has 7 groups of settings.
MA
n
Manual mode
LO
c
Locking the thermostat
OF
F
Switching off the thermostat
SE
t1
Temperature, date and time settings
SE
t2
Weekly schedule setting
SE
t3
Service menu
OK
Saving the parameters and leaving the service menu
1. MAn – manual mode
The temperature is set manually regardless of the weekly
schedule and is kept. Enter the menu and press the knob on
the item
Man,
the option ON (switched on) appears. By
turning the knob select the requested state and confirm by
pressing. The temperatures
tLo
and
tHi
determine the regulation range pre-
programmed in the service menu SE t3, in which you can select the temperature by
turning the knob. Choose the requested temperature. If the chosen temperature is
lower than the required temperature, the thermostat shows the symbol
(▲)
on its
LCD display. By entering the menu
Man
and confirming the option
OFF
, manual
mode is terminated.
2. LOc – Locking the thermostat
To protect the thermostat against unwanted manipulation you
can lock the thermostat. Enter the menu and press the knob
on the item
LOc,
the options
ON/OFF
appear. By turning the
knob select the requested state and confirm by pressing.
Choosing
ON
enables the function
Lock
, and blocks thermostat control. To unlock
the thermostat choose the option
OFF.
Locking the thermostat is indicated on the
LCD by the
symbol.
3. OFF – Switching off the thermostat
The thermostat can be switched off by the option
OFF
.
Enter the menu and press the knob on the item
OFF,
the
options
ON/OFF
appear. By turning the knob select the
requested state and confirm by pressing. Choosing
ON
enables the function
OFF
, and switches off the thermostat. This is indicated on the
LCD by the text
OFF
. Although the thermostat has been switched off, it still
measures and detects the antifreeze temperature (see SE t3, Stby). To unlock the
thermostat enter the menu and choose the option
OFF.
When the knob is pressed
the thermostat will be unlocked.
4. Set1 - Temperature, date and time settings
In the Set1 menu the comfort temperature ( ), the economy
temperature ( ), the temperature for Holiday mode ( ), and
the data and time can be preset. Enter the menu
Set1
, and
on the LCD the symbol of the economy temperature starts
flashing. By turning the knob select the requested item ( , or ), by pressing the
knob the symbols for temperature start flashing and again by turning the knob set the
required temperature and by repeatedly pressing the knob confirm this setting. The
last item serves for setting the current time. It indicates using flashing symbols of the
days of the week. By pressing you enter the current time setting. It starts with the
year. Pressing gets it flashing, and by turning the knob set the year, by pressing
again it saves the setting and then you continue the same way in setting the current
month, day, hour and minute. Then by pressing the knob after the minute setting the
values are saved and the thermostat is back in the menu
Set1
. Select the item
OK
to
leave this menu.
5. SEt2 – Weekly schedule setting
The heating program for switching the comfort and the economy temperatures can
be set for every single day independently (Mo - Monday, Tu - Tuesday, We -
Wednesday, Th - Thursday, Fr - Friday, Sa - Saturday, Su - Sunday) or it can be
split into working days and the weekend. There is one more option - the same
settings for all days with no difference.
Enter the menu
Set2
, and by turning the knob select the combination of days which
is required. Confirm by briefly pressing the knob. It enters the programming of heating
time periods when the thermostat switches between the day temperature and the
night temperature.
Programming always starts at 00 hrs. By turning the knob
clockwise, you can move through the time line. Press the
knob at the point from which you want to start with the
heating to the comfort temperature. The symbol changes
to the . Now by turning the knob clockwise the points
appear which represent the hours for which heating is
performed to the economy temperature. By turning the
knob anti-clockwise the points are erased. Pressing the
knob more switches the economy temperature to the
comfort temperature. By repeating this procedure the
comfort and economy temperatures can be set for a
selected day (or for a group of a few days). After the
programming of the whole day has been finished, the
thermostat shows you
OK
. When the knob is pressed, all
settings are saved.
6. SEt3 – Service menu
The service parameters can be pre-programmed here. In normal mode it is not
necessary to change those parameters. The Service menu includes 9 items. Open
by scrolling the knob to the requested item and by pressing the knob to enter the
programming mode. Select the value again by scrolling the knob. Confirm it by
pressing the knob and it returns you back to the service menu.
TP-155 Wireless programmable indoor thermostat
1 / 2
MMC51701
TP-155 Wireless programmable indoor thermostat
The TP-155 is a wireless programmable indoor thermostat with a weekly heating
schedule. It can regulate the
economical or comfort temperature
inside residential buildings. It offers a
few programmable modes. Every
mode regulates pre-set temperatures
(Comfort, Economy, Holiday, and
Party). The thermostat is able to
measure the thermal inertia inside the
premises and adjust the weekly
schedule
for the requested
temperature to be reached at the pre-
set time.
Figure 1
: 1- knob (encoder) combined with button; 2- tab
Thermostat installation
The product can only be used in an indoor environment. Install the thermostat 1.5
m above the floor in a place where there is good natural air circulation. Don´t install
the thermostat where the measuring can be influenced by drafts, sunlight, heaters or
any other effects. Avoid mounting the thermostat on metal objects or metal bases
which block radio communication.
1. By pressing the tab (by screwdriver for instance) release the front part of the
thermostat.
2. Install the rear part of the thermostat at the chosen place (tab down).
3. Insert the batteries, the polarity is marked on the plastic.
4. Put back the front thermostat part and close it.
Enrolling the thermostat
Install and connect the receiving unit to the heating appliance. If the receiver has
been bought independently, you have to enroll the thermostat to it first. Open the
enrollment mode on the receiver (see its manual) and insert the batteries into the
thermostat or press and hold the knob for 5s. In both cases the thermostat will send
an enrollment signal. The text
LRn
appears on the LCD display when the enrolling
procedure (with AC-116 only) has been done successfully.
Symbols on the LCD:
Figure 2: 1 – Symbols for
comfort and economical
temperatures; 2 – The days of
the week; 3 – Locking the
thermostat; 4 – Alarm tempe-
rature
–
limits / loss of
communication; 5 – Heating
ON / OFF; 6 – Holiday; 7 – Party;
8 – Heating times; 9 – Symbols
for showing temperature time
and texts; 10 – Low battery
Settings and programming
Do the complete settings using the knob – encoder. By pressing the knob 2 sec
enter the programming mode.
General rules for programming:
1. Flashing of any icon on the LCD allows changing the option(s) or choosing a
next item.
2. Perform choosing or changing by turning the knob (turning the knob is possible
from left to right and vice versa).
3. Confirm the selection or change by briefly pressing the knob.
4. When the value of an item has been changed, then after this briefly press the
knob and the changes are saved. Then the thermostat goes to the next item in
the programming menu.
5. After the setting / change of the chosen items, select the parameter „OK“, in the
menu. By short pressing the system returns back to the previous menu (up to
the main menu).
6. If there is no manipulation of the knob for 30 sec, it returns you back to the
previous menu automatically.
The basic menu has 7 groups of settings.
MA
n
Manual mode
LO
c
Locking the thermostat
OF
F
Switching off the thermostat
SE
t1
Temperature, date and time settings
SE
t2
Weekly schedule setting
SE
t3
Service menu
OK
Saving the parameters and leaving the service menu
1. MAn – manual mode
The temperature is set manually regardless of the weekly
schedule and is kept. Enter the menu and press the knob on
the item
Man,
the option ON (switched on) appears. By
turning the knob select the requested state and confirm by
pressing. The temperatures
tLo
and
tHi
determine the regulation range pre-
programmed in the service menu SE t3, in which you can select the temperature by
turning the knob. Choose the requested temperature. If the chosen temperature is
lower than the required temperature, the thermostat shows the symbol
(▲)
on its
LCD display. By entering the menu
Man
and confirming the option
OFF
, manual
mode is terminated.
2. LOc – Locking the thermostat
To protect the thermostat against unwanted manipulation you
can lock the thermostat. Enter the menu and press the knob
on the item
LOc,
the options
ON/OFF
appear. By turning the
knob select the requested state and confirm by pressing.
Choosing
ON
enables the function
Lock
, and blocks thermostat control. To unlock
the thermostat choose the option
OFF.
Locking the thermostat is indicated on the
LCD by the
symbol.
3. OFF – Switching off the thermostat
The thermostat can be switched off by the option
OFF
.
Enter the menu and press the knob on the item
OFF,
the
options
ON/OFF
appear. By turning the knob select the
requested state and confirm by pressing. Choosing
ON
enables the function
OFF
, and switches off the thermostat. This is indicated on the
LCD by the text
OFF
. Although the thermostat has been switched off, it still
measures and detects the antifreeze temperature (see SE t3, Stby). To unlock the
thermostat enter the menu and choose the option
OFF.
When the knob is pressed
the thermostat will be unlocked.
4. Set1 - Temperature, date and time settings
In the Set1 menu the comfort temperature ( ), the economy
temperature ( ), the temperature for Holiday mode ( ), and
the data and time can be preset. Enter the menu
Set1
, and
on the LCD the symbol of the economy temperature starts
flashing. By turning the knob select the requested item ( , or ), by pressing the
knob the symbols for temperature start flashing and again by turning the knob set the
required temperature and by repeatedly pressing the knob confirm this setting. The
last item serves for setting the current time. It indicates using flashing symbols of the
days of the week. By pressing you enter the current time setting. It starts with the
year. Pressing gets it flashing, and by turning the knob set the year, by pressing
again it saves the setting and then you continue the same way in setting the current
month, day, hour and minute. Then by pressing the knob after the minute setting the
values are saved and the thermostat is back in the menu
Set1
. Select the item
OK
to
leave this menu.
5. SEt2 – Weekly schedule setting
The heating program for switching the comfort and the economy temperatures can
be set for every single day independently (Mo - Monday, Tu - Tuesday, We -
Wednesday, Th - Thursday, Fr - Friday, Sa - Saturday, Su - Sunday) or it can be
split into working days and the weekend. There is one more option - the same
settings for all days with no difference.
Enter the menu
Set2
, and by turning the knob select the combination of days which
is required. Confirm by briefly pressing the knob. It enters the programming of heating
time periods when the thermostat switches between the day temperature and the
night temperature.
Programming always starts at 00 hrs. By turning the knob
clockwise, you can move through the time line. Press the
knob at the point from which you want to start with the
heating to the comfort temperature. The symbol changes
to the . Now by turning the knob clockwise the points
appear which represent the hours for which heating is
performed to the economy temperature. By turning the
knob anti-clockwise the points are erased. Pressing the
knob more switches the economy temperature to the
comfort temperature. By repeating this procedure the
comfort and economy temperatures can be set for a
selected day (or for a group of a few days). After the
programming of the whole day has been finished, the
thermostat shows you
OK
. When the knob is pressed, all
settings are saved.
6. SEt3 – Service menu
The service parameters can be pre-programmed here. In normal mode it is not
necessary to change those parameters. The Service menu includes 9 items. Open
by scrolling the knob to the requested item and by pressing the knob to enter the
programming mode. Select the value again by scrolling the knob. Confirm it by
pressing the knob and it returns you back to the service menu.
TP-155 Wireless programmable indoor thermostat
1 / 2
MMC51701
TP-155 Wireless programmable indoor thermostat
The TP-155 is a wireless programmable indoor thermostat with a weekly heating
schedule. It can regulate the
economical or comfort temperature
inside residential buildings. It offers a
few programmable modes. Every
mode regulates pre-set temperatures
(Comfort, Economy, Holiday, and
Party). The thermostat is able to
measure the thermal inertia inside the
premises and adjust the weekly
schedule
for the requested
temperature to be reached at the pre-
set time.
Figure 1
: 1- knob (encoder) combined with button; 2- tab
Thermostat installation
The product can only be used in an indoor environment. Install the thermostat 1.5
m above the floor in a place where there is good natural air circulation. Don´t install
the thermostat where the measuring can be influenced by drafts, sunlight, heaters or
any other effects. Avoid mounting the thermostat on metal objects or metal bases
which block radio communication.
1. By pressing the tab (by screwdriver for instance) release the front part of the
thermostat.
2. Install the rear part of the thermostat at the chosen place (tab down).
3. Insert the batteries, the polarity is marked on the plastic.
4. Put back the front thermostat part and close it.
Enrolling the thermostat
Install and connect the receiving unit to the heating appliance. If the receiver has
been bought independently, you have to enroll the thermostat to it first. Open the
enrollment mode on the receiver (see its manual) and insert the batteries into the
thermostat or press and hold the knob for 5s. In both cases the thermostat will send
an enrollment signal. The text
LRn
appears on the LCD display when the enrolling
procedure (with AC-116 only) has been done successfully.
Symbols on the LCD:
Figure 2: 1 – Symbols for
comfort and economical
temperatures; 2 – The days of
the week; 3 – Locking the
thermostat; 4 – Alarm tempe-
rature
–
limits / loss of
communication; 5 – Heating
ON / OFF; 6 – Holiday; 7 – Party;
8 – Heating times; 9 – Symbols
for showing temperature time
and texts; 10 – Low battery
Settings and programming
Do the complete settings using the knob – encoder. By pressing the knob 2 sec
enter the programming mode.
General rules for programming:
1. Flashing of any icon on the LCD allows changing the option(s) or choosing a
next item.
2. Perform choosing or changing by turning the knob (turning the knob is possible
from left to right and vice versa).
3. Confirm the selection or change by briefly pressing the knob.
4. When the value of an item has been changed, then after this briefly press the
knob and the changes are saved. Then the thermostat goes to the next item in
the programming menu.
5. After the setting / change of the chosen items, select the parameter „OK“, in the
menu. By short pressing the system returns back to the previous menu (up to
the main menu).
6. If there is no manipulation of the knob for 30 sec, it returns you back to the
previous menu automatically.
The basic menu has 7 groups of settings.
MA
n
Manual mode
LO
c
Locking the thermostat
OF
F
Switching off the thermostat
SE
t1
Temperature, date and time settings
SE
t2
Weekly schedule setting
SE
t3
Service menu
OK
Saving the parameters and leaving the service menu
1. MAn – manual mode
The temperature is set manually regardless of the weekly
schedule and is kept. Enter the menu and press the knob on
the item
Man,
the option ON (switched on) appears. By
turning the knob select the requested state and confirm by
pressing. The temperatures
tLo
and
tHi
determine the regulation range pre-
programmed in the service menu SE t3, in which you can select the temperature by
turning the knob. Choose the requested temperature. If the chosen temperature is
lower than the required temperature, the thermostat shows the symbol
(▲)
on its
LCD display. By entering the menu
Man
and confirming the option
OFF
, manual
mode is terminated.
2. LOc – Locking the thermostat
To protect the thermostat against unwanted manipulation you
can lock the thermostat. Enter the menu and press the knob
on the item
LOc,
the options
ON/OFF
appear. By turning the
knob select the requested state and confirm by pressing.
Choosing
ON
enables the function
Lock
, and blocks thermostat control. To unlock
the thermostat choose the option
OFF.
Locking the thermostat is indicated on the
LCD by the
symbol.
3. OFF – Switching off the thermostat
The thermostat can be switched off by the option
OFF
.
Enter the menu and press the knob on the item
OFF,
the
options
ON/OFF
appear. By turning the knob select the
requested state and confirm by pressing. Choosing
ON
enables the function
OFF
, and switches off the thermostat. This is indicated on the
LCD by the text
OFF
. Although the thermostat has been switched off, it still
measures and detects the antifreeze temperature (see SE t3, Stby). To unlock the
thermostat enter the menu and choose the option
OFF.
When the knob is pressed
the thermostat will be unlocked.
4. Set1 - Temperature, date and time settings
In the Set1 menu the comfort temperature ( ), the economy
temperature ( ), the temperature for Holiday mode ( ), and
the data and time can be preset. Enter the menu
Set1
, and
on the LCD the symbol of the economy temperature starts
flashing. By turning the knob select the requested item ( , or ), by pressing the
knob the symbols for temperature start flashing and again by turning the knob set the
required temperature and by repeatedly pressing the knob confirm this setting. The
last item serves for setting the current time. It indicates using flashing symbols of the
days of the week. By pressing you enter the current time setting. It starts with the
year. Pressing gets it flashing, and by turning the knob set the year, by pressing
again it saves the setting and then you continue the same way in setting the current
month, day, hour and minute. Then by pressing the knob after the minute setting the
values are saved and the thermostat is back in the menu
Set1
. Select the item
OK
to
leave this menu.
5. SEt2 – Weekly schedule setting
The heating program for switching the comfort and the economy temperatures can
be set for every single day independently (Mo - Monday, Tu - Tuesday, We -
Wednesday, Th - Thursday, Fr - Friday, Sa - Saturday, Su - Sunday) or it can be
split into working days and the weekend. There is one more option - the same
settings for all days with no difference.
Enter the menu
Set2
, and by turning the knob select the combination of days which
is required. Confirm by briefly pressing the knob. It enters the programming of heating
time periods when the thermostat switches between the day temperature and the
night temperature.
Programming always starts at 00 hrs. By turning the knob
clockwise, you can move through the time line. Press the
knob at the point from which you want to start with the
heating to the comfort temperature. The symbol changes
to the . Now by turning the knob clockwise the points
appear which represent the hours for which heating is
performed to the economy temperature. By turning the
knob anti-clockwise the points are erased. Pressing the
knob more switches the economy temperature to the
comfort temperature. By repeating this procedure the
comfort and economy temperatures can be set for a
selected day (or for a group of a few days). After the
programming of the whole day has been finished, the
thermostat shows you
OK
. When the knob is pressed, all
settings are saved.
6. SEt3 – Service menu
The service parameters can be pre-programmed here. In normal mode it is not
necessary to change those parameters. The Service menu includes 9 items. Open
by scrolling the knob to the requested item and by pressing the knob to enter the
programming mode. Select the value again by scrolling the knob. Confirm it by
pressing the knob and it returns you back to the service menu.
TP-155 Wireless programmable indoor thermostat
1 / 2
MMC51701
TP-155 Wireless programmable indoor thermostat
The TP-155 is a wireless programmable indoor thermostat with a weekly heating
schedule. It can regulate the
economical or comfort temperature
inside residential buildings. It offers a
few programmable modes. Every
mode regulates pre-set temperatures
(Comfort, Economy, Holiday, and
Party). The thermostat is able to
measure the thermal inertia inside the
premises and adjust the weekly
schedule
for the requested
temperature to be reached at the pre-
set time.
Figure 1
: 1- knob (encoder) combined with button; 2- tab
Thermostat installation
The product can only be used in an indoor environment. Install the thermostat 1.5
m above the floor in a place where there is good natural air circulation. Don´t install
the thermostat where the measuring can be influenced by drafts, sunlight, heaters or
any other effects. Avoid mounting the thermostat on metal objects or metal bases
which block radio communication.
1. By pressing the tab (by screwdriver for instance) release the front part of the
thermostat.
2. Install the rear part of the thermostat at the chosen place (tab down).
3. Insert the batteries, the polarity is marked on the plastic.
4. Put back the front thermostat part and close it.
Enrolling the thermostat
Install and connect the receiving unit to the heating appliance. If the receiver has
been bought independently, you have to enroll the thermostat to it first. Open the
enrollment mode on the receiver (see its manual) and insert the batteries into the
thermostat or press and hold the knob for 5s. In both cases the thermostat will send
an enrollment signal. The text
LRn
appears on the LCD display when the enrolling
procedure (with AC-116 only) has been done successfully.
Symbols on the LCD:
Figure 2: 1 – Symbols for
comfort and economical
temperatures; 2 – The days of
the week; 3 – Locking the
thermostat; 4 – Alarm tempe-
rature
–
limits / loss of
communication; 5 – Heating
ON / OFF; 6 – Holiday; 7 – Party;
8 – Heating times; 9 – Symbols
for showing temperature time
and texts; 10 – Low battery
Settings and programming
Do the complete settings using the knob – encoder. By pressing the knob 2 sec
enter the programming mode.
General rules for programming:
1. Flashing of any icon on the LCD allows changing the option(s) or choosing a
next item.
2. Perform choosing or changing by turning the knob (turning the knob is possible
from left to right and vice versa).
3. Confirm the selection or change by briefly pressing the knob.
4. When the value of an item has been changed, then after this briefly press the
knob and the changes are saved. Then the thermostat goes to the next item in
the programming menu.
5. After the setting / change of the chosen items, select the parameter „OK“, in the
menu. By short pressing the system returns back to the previous menu (up to
the main menu).
6. If there is no manipulation of the knob for 30 sec, it returns you back to the
previous menu automatically.
The basic menu has 7 groups of settings.
MA
n
Manual mode
LO
c
Locking the thermostat
OF
F
Switching off the thermostat
SE
t1
Temperature, date and time settings
SE
t2
Weekly schedule setting
SE
t3
Service menu
OK
Saving the parameters and leaving the service menu
1. MAn – manual mode
The temperature is set manually regardless of the weekly
schedule and is kept. Enter the menu and press the knob on
the item
Man,
the option ON (switched on) appears. By
turning the knob select the requested state and confirm by
pressing. The temperatures
tLo
and
tHi
determine the regulation range pre-
programmed in the service menu SE t3, in which you can select the temperature by
turning the knob. Choose the requested temperature. If the chosen temperature is
lower than the required temperature, the thermostat shows the symbol
(▲)
on its
LCD display. By entering the menu
Man
and confirming the option
OFF
, manual
mode is terminated.
2. LOc – Locking the thermostat
To protect the thermostat against unwanted manipulation you
can lock the thermostat. Enter the menu and press the knob
on the item
LOc,
the options
ON/OFF
appear. By turning the
knob select the requested state and confirm by pressing.
Choosing
ON
enables the function
Lock
, and blocks thermostat control. To unlock
the thermostat choose the option
OFF.
Locking the thermostat is indicated on the
LCD by the
symbol.
3. OFF – Switching off the thermostat
The thermostat can be switched off by the option
OFF
.
Enter the menu and press the knob on the item
OFF,
the
options
ON/OFF
appear. By turning the knob select the
requested state and confirm by pressing. Choosing
ON
enables the function
OFF
, and switches off the thermostat. This is indicated on the
LCD by the text
OFF
. Although the thermostat has been switched off, it still
measures and detects the antifreeze temperature (see SE t3, Stby). To unlock the
thermostat enter the menu and choose the option
OFF.
When the knob is pressed
the thermostat will be unlocked.
4. Set1 - Temperature, date and time settings
In the Set1 menu the comfort temperature ( ), the economy
temperature ( ), the temperature for Holiday mode ( ), and
the data and time can be preset. Enter the menu
Set1
, and
on the LCD the symbol of the economy temperature starts
flashing. By turning the knob select the requested item ( , or ), by pressing the
knob the symbols for temperature start flashing and again by turning the knob set the
required temperature and by repeatedly pressing the knob confirm this setting. The
last item serves for setting the current time. It indicates using flashing symbols of the
days of the week. By pressing you enter the current time setting. It starts with the
year. Pressing gets it flashing, and by turning the knob set the year, by pressing
again it saves the setting and then you continue the same way in setting the current
month, day, hour and minute. Then by pressing the knob after the minute setting the
values are saved and the thermostat is back in the menu
Set1
. Select the item
OK
to
leave this menu.
5. SEt2 – Weekly schedule setting
The heating program for switching the comfort and the economy temperatures can
be set for every single day independently (Mo - Monday, Tu - Tuesday, We -
Wednesday, Th - Thursday, Fr - Friday, Sa - Saturday, Su - Sunday) or it can be
split into working days and the weekend. There is one more option - the same
settings for all days with no difference.
Enter the menu
Set2
, and by turning the knob select the combination of days which
is required. Confirm by briefly pressing the knob. It enters the programming of heating
time periods when the thermostat switches between the day temperature and the
night temperature.
Programming always starts at 00 hrs. By turning the knob
clockwise, you can move through the time line. Press the
knob at the point from which you want to start with the
heating to the comfort temperature. The symbol changes
to the . Now by turning the knob clockwise the points
appear which represent the hours for which heating is
performed to the economy temperature. By turning the
knob anti-clockwise the points are erased. Pressing the
knob more switches the economy temperature to the
comfort temperature. By repeating this procedure the
comfort and economy temperatures can be set for a
selected day (or for a group of a few days). After the
programming of the whole day has been finished, the
thermostat shows you
OK
. When the knob is pressed, all
settings are saved.
6. SEt3 – Service menu
The service parameters can be pre-programmed here. In normal mode it is not
necessary to change those parameters. The Service menu includes 9 items. Open
by scrolling the knob to the requested item and by pressing the knob to enter the
programming mode. Select the value again by scrolling the knob. Confirm it by
pressing the knob and it returns you back to the service menu.
TP-155 Wireless programmable indoor thermostat
1 / 2
MMC51701
