9
TOP PANEL CONTROLS: SWITCHES AND ADJUSTMENT CONTROLS
B CH LEVELS (0.3 ÷ 5V):
B channels input sensitivity
adjustment control
. Set to 1 position. Use a CD as source,
increase head unit volume until output distorts, then decrease
volume by 1 step in order to eliminate distortion.
Turn LEVELS up until sound becomes distorted, then turn
LEVELS down a bit for optimum sound.
PASS MODE (HI - FULL - LO):
B channels filter switch
.
Select
FULL
to drive full range power outputs. The full frequency
bandwidth will be output to power output connectors.
Select
HI
for Hi-pass to drive a MIDRANGE / TWEETER.
Select
LO
for Lo-pass to drive a SUB / WOOFER / MIDRANGE.
MODE (ST - MO(R):
Select
ST
to set B channels to stereo
mode. Left and Right input signals drive Left and Right power
outputs. Select
MO(R)
for mono (bridge) operation. With this
setup the Right input channel drives BR and BL power output,
so connect loudspeaker to BL- and BR+ for proper bridge
connection.
XOVER (80 Hz ÷ 3.3 kHz):
B channels crossover point
adjustment
. Rotating the knob you can select any frequencies
between 80 Hz and 3.3 kHz. The frequencies above crossover
point will be attenuated at 12dB/Oct.
A CH LEVELS (0.3 ÷ 5V):
A channels input sensitivity
adjustment control
. Set to 1 position. Use a CD as source,
increase head unit volume until output distorts, then decrease
volume by 1 step in order to eliminate distortion. Turn LEVELS
up until sound becomes distorted, then turn LEVELS down
a bit for optimum sound.
PASS MODE (HI - FULL - LO):
A channels filter switch
.
Select
FULL
to drive full range power outputs.
The full frequencies bandwidth will be output to power output
connectors. Select
HI
for Hi-pass to drive a MIDRANGE /
TWEETER. Select
LO
for Lo-pass to drive a SUB / WOOFER /
MIDRANGE.
MODE (ST - MO(R):
Select
ST
to set A channels to stereo
mode. Left and Right input signals drive Left and Right power
outputs. Select
MO(R)
for mono (bridge) operation. With this
setup the Right input channel drives AR and AL power output,
so connect loudspeaker to AL- and AR+ for proper bridge
connection.
XOVER (50 Hz ÷ 500 Hz):
A channels crossover point
adjustment
. Rotating the knob you can select any frequency
between 50 Hz and 500 Hz. The frequencies over crossover
point will be attenuated at 12dB/Oct.
MULTIPLIER (x1 - x10):
Select
X1
for normal frequency range
(50 Hz - 500 Hz) of A channel filter (Hi-pass or Lo-pass).
Select
X10
for crossover point multiplied by 10 (500 Hz - 5 kHz).
ON:
Power LED
. It lights up when you turn on the amplifier. If
all LEDs (10) (11) (12) (13) turn on at the same time, the amplifier
will shut down and you will have to contact a service centre.
TH:
Thermal status LED
. It lights up when thermal protection
is active, above 85°C. The amplifier shuts down until the chassis
temperature goes below 75°C.
OVL:
Overload status
LED
. It lights up when overload
occurs on the power output terminals. The amplifier goes in
muting for 3 seconds and this LED starts flashing until you turn
off the amplifier.
REMOVE THE CAUSE OF OVERLOAD.
SPK:
Speaker status LED
. It lights up when a speaker touches
the car body. The amplifier goes in muting for 3 seconds and
this LED starts flashing until you turn off the amplifier.
REMOVE THE CONTACT BETWEEN SPEAKER WIRE AND
CAR BODY.
1
2
3
4
5
6
7
8
5
6
9
10
11
12
13
7
8
9
12
10
11
13
1
3
4
2
HI FULL LO
ST MO (R)
ON OVL
TH SPK
B - ch
1
3
4
2
5
max
LEVELS PASS MODE
MODE
HI FULL LO
ST MO (R)
LEVELS PASS MODE
MODE
X1 X10
MULTIPLIER
XOVER
1
3
4
2
5
max
80
3.3k
160
800
XOVER
50
500
100
250
A - ch
HDP4
HDP 4
Advanced Web Manual
Содержание HDP 4
Страница 1: ...www hertzaudiovideo com Release 1 0 Revisione1 0 UK IT HDP 4 ...
Страница 23: ...23 ...
Страница 30: ...30 COME RUOTARE IL LOGO HERTZ 180 PUSH Remove and Rotate 180 1 2 3 4 5 6 7 8 9 HDP 4 Advanced Web Manual ...
Страница 45: ...45 ...
