Hercules Rob Family F360, Перевод оригинальной инструкции по эксплуатации, Страница: 29 / 101

MY21H01 - 32_1.0_30.07.2020
29
Overview
Applies only to eShift with Shimano DI2 automatic hub gears
Applies only to eShift with NuVinci H|Sync/enviolo with
Optimized H|Sync
Applies only to eShift with Rohloff E-14 Speedhub 500/14.
3.7.6 System message
The drive system monitors itself continuously and
if an error is detected, it is indicated by a system
message. The system may switch off
automatically depending on the type of error. You
will find information and a table for all system
messages in Section
6.2 .
3.7.7 ABS indicator lamp
The anti-blocking system indicator lamp must light
up after the system has started up and must go
out once speed has reached about 5 km/h. If the
ABS indicator lamp remains unlit when the electric
drive system starts, the ABS is defective. An error
code on the display screen also tells the rider that
it is defective. If the indicator lamp does not go out
after you set off or it lights up while you are riding,
this means there is an error in the anti-blocking
system. The anti-blocking system is inactive in
such a case. The brake system itself remains
functional. It is only the anti-blocking system
control which no longer operates.
If the ABS indicator lamp is lit, the ABS function is
disabled.
Indicator Change
Gear adjustment You can use this menu option to
make a fine adjustment to the
Shimano DI2. You'll find the
specified setting range in the gear
manufacturer's operating
instructions. Make the fine
adjustment as soon as you hear any
unusual noises from the gear shift.
This menu option is only shown
when the display is positioned in its
mount.
Gear recovery You can use this menu option to
reset the rear derailleur if it has been
detached – due to a crash or impact
against the derailleur, for example.
You will find a description of how to
reset the gear shift in the gear shift
manufacturer's operating
instructions. This menu option is
only shown when the display is
positioned in its mount.
Gear vx.x.x.x: this is the gear software version.
This menu option is only shown
when the display is positioned in its
mount. This menu option is only
shown if you have an electronic
control gear.
Table 32: Changing the system settings
Indicator Change
Gear calibration This is where you can perform a
calibration on the stepless gear.
Press on the Lighting button to
confirm calibration. Then follow the
instructions. You might need to
perform calibration while riding in
the event of a fault. In such cases,
you press on the "Lighting" button
to confirm you require calibration
and then follow the instructions on
the display screen. This menu
option is only shown when the
display is positioned in its mount.
Gear vx.x.x.x: this is the gear software version.
This menu option is only shown
when the display is positioned in its
mount. This menu option is only
shown if you have an electronic
control gear.
Table 33: Changing the system settings
Indicator Change
Start gear This is where you can set the start
gear. The automatic gear switch
function is switched off in
Position – –.
This menu option is only shown if
the display is positioned in its
mount.
Gear vx.x.x.x: this is the gear software version.
This menu option is only shown
when the display is positioned in its
mount. This menu option is only
shown if you have an electronic
control gear.
Table 34: Changing the system settings
Notice
The anti-blocking system indicator lamp may light
up if the front and rear wheels are rotating at
widely different speeds from one another – for
example, if the rider cycles on the rear wheel only
or if a wheel is rotating for a unusually long time
without making contact with the ground (fitting
stand). The anti-blocking system switches off in
such cases.
1 Stop pedelec to reactivate the anti-blocking
system.
2 Restart pedelec (turn off and on again).