Hercules HE79 Скачать руководство пользователя страница 6

Страница: 6 / 16

Page 6

For technical questions, please call 1-888-866-5797.

Item 56790

Warning Symbols and Definitions

This is the safety alert symbol. It is used to

alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to
avoid possible injury or death.

Indicates a hazardous
situation which, if not

avoided, will result in death or serious injury.

Indicates a hazardous
situation which, if not

avoided, could result in death or serious injury.

Indicates a hazardous
situation which, if not

avoided, could result in minor or moderate injury.

Addresses practices not

related to personal injury.

Symbology

Volts

Alternating Current

Amperes

n0 xxxx/min.

No Load Revolutions per Minute (RPM)

WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
safety goggles with side shields.

Read the manual before set-up and/or use.

WARNING marking concerning
Risk of Electric Shock.
Properly connect power cord
to appropriate outlet.

Keep hands clear of fence area.

DANGER marking concerning
Risk of Amputation.
Keep hands well clear of cutting area.

Specifications

Electrical Rating

120 VAC / 60 Hz / 15 A

Spindle No Load Speed

4100 /min

Max. Accessory Diameter

Cut-Off Wheel Diameter – 14"

Arbor

1" Round

Cutting Capacity

SETUP - BEFORE USE

Read the ENTIRE IMPORTANT SAFETY
INFORMATION section at the beginning
of this manual including all text under

subheadings therein before set up or use of
this product.
Note:

For additional information regarding

the parts listed in the following pages, refer to

Parts List and Diagram

on page 12.

Mounting

1. Use the four bolt holes provided in the Base

to mount the Cut-Off Saw to a stable support
before use. Mounting hardware not included.

2. Ensure that the Cut-Off Saw is always stable

and secure (e.g. fixed to a bench).

Work Area

1. Designate a work area that is clean and well lit.

The work area must not allow access by children
or pets to prevent distraction and injury.

2. There must not be objects, such as utility lines,

nearby that will present a hazard while working.

3. Route the power cord along a safe route to reach

the work area without creating a tripping hazard or
exposing the power cord to possible damage. The
power cord must reach the work area with enough
extra length to allow free movement while working.

Cut-Off Wheel Selection

1. Any cut-off wheel that will be used must be

marked as suitable for the material to be cut.

2. Use only a cut-off wheel diameter in accordance

with the markings on the saw. See specification
table for the bore diameter of the cut-off wheel.

3. Use only cut-off wheels that are marked with a speed

equal or higher than the speed marked on the tool.

Guard Setup

Check that the Lower Blade Guard is in place,
moves freely, and closes instantly.

Содержание HE79

















Результаты поиска

Содержание HE79

Отзывы:

Бренды по названию

Популярные бренды

Hercules HE79, Руководство пользователя и инструкции по безопасности

Результаты поиска

Содержание HE79

Отзывы:

Бренды по названию

Популярные бренды