manualshive.com logo in svg

Henkelman Jumbo 30, Руководство пользователя, Страница: 34 / 44

Поделиться
Скачать
Henkelman Jumbo 30 Скачать руководство пользователя страница 34

8    Troubleshooting and Error Codes

The tables below show the possible malfunctions and the corresponding causes as well as the
steps to be taken.

Malfunction

Activity

More information

Control panel does not illumin-
ate.

•

Connect the machine to the
power supply.

Connecting the Machine on
page 17

Electrical Installation on page
40

The control panel is on, but
there is no activity after closing
the lid.

•

Check or adjust the switch
of the lid.

Contact your supplier.

Insufficient end vacuum.

•

Check the vacuum settings
of the programme and ad-
just them.

•

Make sure that the extrac-
tion opening is not covered.

•

Check the oil level in the
pump.

•

Check/replace the oil ex-
haust filter.

•

Check/replace the lid gas-
ket.

Operation  on page 19.

Vacuum Pump maintenance on
page 28.

Replacing the Oil Exhaust Filter
on page 31.

Replacing the Lid Gasket on
page 27.

Vacuum process is slow.

•

Make sure that the extrac-
tion opening is not covered.

•

Check the oil level in the
pump.

•

Check/replace the oil ex-
haust filter.

Vacuum Pump maintenance on
page 28.

Replacing the Oil Exhaust Filter
on page 31.

Troubleshooting and Error Codes    34

Содержание Jumbo 30













































Отзывы:

Нет отзывов