background image

1   Please observe the following 

1.4   For Your Safety 

   

  For safe and successful operation of the unit, read these instructions completely.  If 

the instructions are not observed, the manufacturer can assume no responsibility. 

  Do not expose the connecting cable to heat, oil, or sharp edges. 

  Make sure the Unit stands stable and secure. 

  Use only original equipment replacement parts. 

  Always disconnect the power supply before servicing the unit. 

  Observe general safety regulations for the handling of chemicals such as Loctite

®

 

adhesives and sealants.  Observe the manufacturer’s instructions as stated in the Safety 
Data Sheet. 

     While under warranty, the unit may be repaired only by an authorized Loctite 

service representative.  

 

 

 

 

Warning! 

 
It is the responsibility of the user to ensure that all devices being driven by the LED Spot Controller 
are set-up in a safe manner. 
 
The manufacturer is in no way responsible for injuries or damage to persons or property resulting 
from devices being driven by the LED Spot Controller. 
 
For safe and successful operation of the unit, read these instructions completely. If the instructions 
are not observed, the manufacturer can assume no responsibility. 
 
Removing, bypassing or putting out of operation any of the safety devices can result in radiation 
damage to persons and damage to the unit and is therefore prohibited! 
 
Do not look directly at LED-UV light, or at LED-UV light reflected in a mirror or other reflective 
surface. Doing so could cause eye damage. 
 
Install the LED head in a way that humans are not exposed to LED-UV light. 
 
Exposure could injure the skin or cause other injury. 
 
If there is a risk of the LED-UV light being exposed to UV reflective light, place the product inside a 
cover with proper reflectance and heat characteristics to block that reflected light. 
 
When operating the controller, set up the system so that the path of the LED-UV light is not at eye 
level. 
 
It is strongly recommended to place a protective barrier around the product so that people cannot 
approach it while it is operating. 
 
Wear protective UV glasses and other protective clothing during operation. 
 
Never operate this product in a manner not described in this manual. Doing so risks exposure to 
LED UV light. 
 
Damage to the power cord or the housing can result in contact with live electrical parts. Check the 
power cord and the unit before each use. If the power cord or the unit is damaged, do not operate! 
Replace a damaged power cord with a new one. 
 
The unit may be opened and repaired only by authorized service personal. 
 

 

 

Содержание 2804959













Отзывы:

Похожие инструкции для 2804959