background image

 

 
 
 
 

 

Evolve – Glass SIM Kit 

DOCUMENT TYPE = FITTING INSTRUCTIONS  

ORIGINAL LANGUAGE = ENGLISH 

 

 

 

        

 

 

 

 

 

 

   

           

 

 

    

 

 

 

 

 

 

 

Maximum door weight

 = 40kg per leaf 

– total system 80kg  

Maximum door width   

2 x 2mtr Track = 760 - 1058mm (Up to 2035 mm clear opening) 

   

 

 

About this document 

This document addresses qualified personnel only. The mounting must be done by technically educated, 
trained and qualified personnel. Electrical wirings have to be completed by suitably qualified specialists. 

These instructions describe how to install the track & sliding door gear 

– for operation of the drive motor & Wiring detail 

for the addition of switches & or sensors please refer the Evolve Motor and Wiring Fitting Instructions supplied 

The manufacturer’s specifications must be respected, in especially maximum weight restriction of the door leaf. Any 
other use of this product is considered inappropriate use. 

It is not guaranteed that this product will work in combination with fittings, motors or other electronic devices 
supplied by other manufactures. 

The appliance is only to be used with the power supply unit provided. 

Before you commence work, please read through these instructions. Please store these instructions in a safe place 
and pass them on to any future owners. Damage resulting from non 

– compliance with these instructions and safety 

instructions will void the warranty. PC Henderson nor the motor unit manufacturer will assume liability for any 
consequential damage. 

 

 

Fixings required

 (Not supplied by PCH) 

We recommend that suitable wall fixings and screws with a Safe Working Load of at least 80kg are used.  

Contents of Kit 

  

80kg 

Содержание Evolve Glass SIM Kit


























Отзывы: