ecoControl App!. A Thermostat indicates the mobile
device connec on by fast blinking red led.
1
Se ngs
Thermostat has several se ngs which can be
adjusted by ecoControl App.
Mode
Thermostat can adjust
floor
temperature,
air
temperature, air temperature with floor limits (
dual
)
or hea ng ra o (
PWM
control) according to mode
selec on.
Floor temperature min and max
This se ng has two main purposes. In floor mode
min and max values specify ac ve range of dial. In
dual mode this se ng does not effect the dial but
thermostat keeps floor temperature between limits.
Feature can be used to protect wooden floors (max
limit) or to guarantee warm floor in room with
fireplace, e.g. Note: N/A in PWM and in air mode.
Air temperature min and max
This se ng has two main purposes. In air mode it
specifies ac ve dial range. In all other modes it can
be used as air frost/over temperature protec on.
Name of thermostat
Name shown in ecoControl App
User program ac vated eco temp
During all green hours in user program the
temperature is adjusted to this value. Also eco bu on
uses this se ng as a target temperature.
Externally ac vated eco temp
During every external pilot signal ac ve me
temperature is modified to this value.
Floor temperature offset (calibra on)
If user's temperature measurement has offset to dial
setpoint this se ng is used to calibrate.
Note, floor
sensor inside floor construc on is much warmer
than real temperatures measured in room. Thus
default is -3C to have rotary dial adjustment range
in realis c area of 18C...24C.
Air temperature offset (calibra on)
If user's temperature measurement has offset
to dial setpoint this se ng is used to calibrate.
PWM min and max
This se ng has two main purposes. In PWM
mode min and max values specify ac ve dial
range. In all other modes it guarantees
maximum pulse ra o. Note: Se ng can be
used, e.g., to limit maximum hea ng power to
comply with installa on standard EN50599.
Valve protec on
Valve protec on turns hea ng ON once per
week for 5 minutes even at summer me. This
se ng is typically used with water carrier floor
hea ng valves. Feature prevents the valve from
ge ng stuck during summer.
Sensor type
Floor sensors from different manufacturers can
be used. Supported types are 2k, 10k, 12.5k,
15k, 33k NTCs.
Led intensity
Intensity of power and eco touch bu ons.
User program mode
AUTO enables user program, OFF disables
2
Week schedule
User can create 7d/24h week schedule in
ecoControl App. With week schedule the user
programs thermostat to decrease temperature
during me slots when room is not used. Green
eco bu on indicates that thermostat is in week
schedule eco slot.
Week schedule execu on needs correct real
me in thermostat.
In case of invalid real me
the week program is deac vated and user is
warned by blinking red and green lights.
Real
me is updated from ecoControl App every
me the thermostat is connected to a mobile
phone. Real me has backup to power
shortages of 2 hours.
3
Error modes
Parallel blinking red and green lights indicate an
error. The most typical case is that real me is
corrupted during too long power break. This is
automa cally solved by taking connec on with
ecoControl app. Use ecoControl App to read an
error code. Possible error codes are
1
Floor sensor fault
2
Over heat
3
Internal fault
10
Calendar me is not valid
You may try to reset fault by using power touch
bu on to so reset or by using ecoControl App
to generate hard reset.
In errors 1, 2, 3 hea ng is permanently off. In
error 10 user program is deac vated.
FI
BLE-termostaa
Asennus- ja käy öohje
BLE-TERMOSTAATIN ASENTAMINEN
TEKNISET TIEDOT
Bluetooth:
Versio 4.2
Käy öjännite:
230V – 50Hz
Maksimikuorma:
16A (resis ivinen)
Käy ölämpä la:
+5°C/+35°C
Ulkoinen ohjaus:
230V - 50Hz
IP-luokka:
IP21
Väri:
Valkoinen
Anturit:
Sisäinen huoneanturi, ulkoinen la a-anturi
NTC. Mahdolllisuus kytkeä ulkoinen langaton anturi
(Bluetooth)
ASENNUS
Tuo een saa asentaa vain valtuute u ja pätevä
asentaja paikallisten määräysten mukaises .
Varmista sähkönsyötön jänni ee ömyys ennen
asennusta.
Asennuspaikan tulee ola BLE:n kantaman sisällä (n.
10m) lähimmästä Ac ce Ahead liiketunnis mesta.
Uudessa lai eessa keskiölevy (A) ja kehys (B) ovat ir
ja voit vetää ne ulos. Jos muoviosat on paine u
paikalleen niin vapautat keskiölevyn painamalla
nuppia (C°) voimakkaas alaspäin ja kääntämällä
samalla vastapäivään. Kehys ja keskiölevy voidaan
nyt vetää ulos.
Kytke johdot termostaa n lii meen:
TIPUTUS:
Ulkoinen ohjaus (jos käytössä),
KUORMA (N):
Kuorman nollajohdin,
N:
Syötön nollajohdin,
FLOOR
SENSOR:
La a-anturi NTC,
KUORMA (L):
kuorman
vaihejohdin,
L:
Syötön vaihejohdin.
2 / 4