background image

 

 

 
 

2.17   BWT technology in a Roxx Premium heater 

 

Bio Water Technology (BWT) uses the heater's thermal energy to heat water and raise the moisture level without 
a separate heat source. Moisturised air improves the sauna climate, and various fragrances and salts can be 
evaporated to make the sauna experience more enjoyable.

 

 

A water container with a lid is delivered with the heater; the container can be installed between the heating elements. 
The water tank can be installed when approximately 2/3 of the heater stones have been stacked. The water tank, even 
when empty, does not need to be removed when the heater is on.  
The tank has a capacity of approximately two litres. Bringing water to the boil when the tank is full takes approximately 1-
2 hours depending on the set temperature. 
It is recommended to pour water into the tank when the heater is turned off. Water is poured through the grate on the lid. 
You can pour less water into the tank if the bathing time is shorter.  

The water tank must be removed and impurities, such as limescale etc. removed every so often. The stones surrounding 
the tank must be removed during cleaning, so that the tank can be lifted more easily. 

When the water is boiling, the moisture levels in the sauna remain high. This means that the temperature can be kept 
lower while still experiencing pleasant heat. More heat and moisture can, if necessary, be created by throwing water on 
the stones on top of the heater. 

Mild fragrance essences, suitable for heater use, can be put in the water tank. 
You can, for example, put mountain salt crystals on the lid of the water tank. They dissolve into the steam and evaporate 
into the air. If mountain salt crystals are placed in the water tank, the salinity of the water will remain 26%. 
 
 

 

3.  Helo Roxx Premium  spare part list 

 

     

 

 
 
 

Tabel 5   Roxx Premium  Spare parts list 

Part 

Part number 

Part name 

Helo Roxx 60 Premium 

Helo Roxx 90 Premium 

4071002 

Rock gate 

5916324 

Circuit board OLEA 103 

7712000 

Strain relief 

7812550 

Mains connector  NLWD 1-1 

6214042 

Thermostat OLET 31 

4316221 

Heating element SEPC 64 

5207518 

Heating element SEPC 65B 

 

5320517 

Contactor OKTA 5-1 

6119649 

Rocker switch 

7306611 

Rubber cover for rocker switch 

15 

Installation and User Manual  

HELO Roxx Premium

 

Содержание 1107-60-040517
















Отзывы: