background image

20

106027

6/10-LBRY

salT Tank asseMbies

Item  

Description  

Qty  

Part #

7-13a    Salt Tank Assy (18x33)-Black 

104411

       b    Salt Tank Assy (18x33)-Blue 

104417 

       c    Salt Tank Assy (18x40)-Black 

104418

       d    Salt Tank (11x11x36)-Black 

104511

  3/8” x 6” Brine Line 

102671

8a 

  18x33 Salt Tank Tank-Black 

104490

  b 

  18x33 Salt Tank Tank-Blue 

104491

  c 

  18x40 Salt Tank Tank-Black 

104492

  d 

  11x11x36 Tank-Black 

104486

  Salt Tank Cover 

Included with 8a,b,c

10-14a   Safety Brine Valve Assy 33” 

101302

         b   Safety Brine Valve Assy 41” 

104172

         c   Safety Brine Valve Assy 

101304

10 

  Cap, Brine Well 4" 

101365

11* 

  Safety Brine Valve  

101274

12 

  Float Assembly 

101660

13 

  Air Check 

101181

14 a,c    Brine Well 33” 

102876 

 

 

 

     b    Brine Well 41” 

102877

15 

  2-Piece Overflow 

102217

16 a,b   Grid Plate 18” / 4" Hole 

101758

     c,d   Grid Plate 11x11 / 4" Hole 

101756

*Safety Brine Valve (Item 11)

Drawing for service only

Must be ordered complete

WATERMATE SERIES WATER SOFTENERS LIMITED WARRANTY

Hellenbrand, Inc., warrants to the original consumer purchaser that the WaterMate and the parts listed below will be free from defects in material and/or workmanship 

from the date of the original installation for the following time periods:
 

For a Period of FIVE YEARS: The control valve including electrical parts, internal parts, and valve body. 

 

For a Period of TEN YEARS: The fiberglass and/or polyglass mineral tanks, 6” Diameter-13” Diameter

 

For a Period of FIVE YEARS: The fiberglass and/or polyglass mineral tanks, 14” Diameter - Up

 

For a Period of FIVE YEARS: The salt storage/cabinet tank.

 

For a Period of ONE YEAR:  Any other component.

Any parts used for replacement are warranted for the remainder of the original warranty period applicable to the part.

 

THIS WARRANTY IS EFFECTIVE TO THE ORIGINAL CONSUMER PURCHASER ONLY, AND ONLY AS LONG AS THE WATERMATE RE-

MAINS AT THE ORIGINAL INSTALLATION SITE.

 

No sales representative, distributor, agent, dealer, reseller or any other person is authorized to make any other warranty on behalf of Hellenbrand, Inc.  Upon 

expiration of the applicable warranty period(s), Hellenbrand, Inc., shall have no further liability related to the products/parts to which the warranty period(s) apply, except 

with respect to valid warranty claims asserted during the appropriate warranty period(s).

 

If a part described above becomes defective within the specified warranty period, you should notify your WaterMate sales representative and arrange a time during 

normal business hours for the inspection of the water conditioner at the original installation site.  Any part found defective within the terms of this warranty will, at Hel-

lenbrand, Inc.’s option, be repaired or replaced.  You are responsible for freight from our factory and local service charges. This paragraph sets forth the exclusive remedy 

for any valid warranty claims against Hellenbrand, Inc.

 

THIS WARRANTY DOES NOT COVER defects caused by sand, sediment or bacteria fouling, accident, fire, flood, Act of God, misuse, misapplication, ne-

glect, alteration, installation or operation contrary to Hellenbrand, Inc.’s printed instructions, or installation, repair or service by anyone other than Hellenbrand, Inc.,  or 

an authorized Hellenbrand reseller. 

 

As a manufacturer, we do not know the characteristics of your water supply or the purpose for which you are purchasing this water conditioner.  Please under-

stand that the quality of water supplies may vary seasonally or over a period of time, and that your water usage rate may vary as well.  Water characteristics can also change 

considerably if your water conditioner is moved to a new location.  For these reasons, we assume no liability for the determination of the proper equipment necessary to 

meet your requirements and we do not authorize others to assume such obligations for us.

 

REMEDIES FOR DEFECTS OR FAILURES, TO THE EXTENT PERMITTED BY APPLICABLE LAW, ARE LIMITED TO THE REMEDIES PRO-

VIDED IN THIS WARRANTY.  ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND ANY WARRANTY WHICH MIGHT ARISE BY IMPLICATION OR 

OPERATION OF LAW, WHETHER FROM THE SELLER AND/OR MANUFACTURER OF THIS PRODUCT, IS HEREBY EXCLUDED AND DISCLAIMED, TO THE 

EXTENT ENFORCEABLE UNDER APPLICABLE LAW, INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FIT-

NESS FOR ANY PARTICULAR PURPOSE OR NON-INFRINGEMENT, OR ANY WARRANTIES ARISING FROM COURSE OF PERFORMANCE, COURSE OF 

DEALING, OR FROM USAGES OF TRADE.  

 

UNDER NO CIRCUMSTANCES SHALL HELLENBRAND, INC., BE LIABLE TO THE ORIGINAL CONSUMER PURCHASER OR TO ANY OTHER 

PERSON FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR FOR ANY OTHER LOSS, DAMAGE, OR EXPENSE OF ANY KIND, 

INCLUDING LOSS OF PROFITS, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT, IN TORT OR OTHERWISE, AND RE-

GARDLESS OF WHETHER HELLENBRAND, INC., WAS AWARE OF THE POSSIBILITY OF SUCH LOSS.  THESE LIMITATIONS WILL APPLY REGARDLESS 

OF ANY FAILURE OF ESSENTIAL PURPOSE OF ANY LIMITED REMEDY.

 

Some states do not allow limitations on how long an implied warranty lasts or exclusions or limitations of incidental or consequential damages, so the above 

limitations or exclusions may not apply to you.  This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Updated 3/06

Содержание WaterMate-1 WM1-16M





















Отзывы: