HELI CPC 20 Скачать руководство пользователя страница 39

Страница: 39 / 98

Fig. 4-5 Inching valve

4.5 Transmission Case

It is used to contain the input shaft, the output shaft, etc. and serve as an oil tank.

There is an oil filter (I)

of 150 meshes in specification at the bottom of the case to

filter the oil from the charging pump. The oil filter (II)

for the pipeline, the oil inlet

cover and the dip stick are all fixed at the top of the case cover.

4.6 Charging Pump (See Fig.4-6)

The charging pump between the torque converter and the input shaft of the

transmission is a gear pump driven by the turbine shaft concluding a pair of inner-

meshed gears for the purpose of feeding the oil to the torque converter and the

transmission.

(1)Snap ring
(2) O-ring
(3) Inching valve rod
(4) Snap ring
(5) Spring
(6) Valve core
(7) Spool
(8) Valve body
(9) Spring
(10) O-ring
(11) Cover
(12) Oil seal

-37-

Содержание CPC 20



































































































Результаты поиска

Содержание CPC 20

Отзывы:

Бренды по названию

Популярные бренды

HELI CPC 20, Руководство пользователя

Результаты поиска

Содержание CPC 20

Отзывы:

Бренды по названию

Популярные бренды