MODEL NUMBER
Index
3-SV
3-TS*
3-PA**
4-GM
4-TS*
4-GMPA**
6-SV
6-PA**
8-SV
8-PA**
No.
Part Name
Part No.
Part No.
Part No.
Part No.
1
Body Casting (Note 1)
3-SV
4-GM
6-SV
8-SV
1
Body Casting (Note 1)
3-TS*
4-TS*
--
--
2
Jaw Casting
3-J
4-J
6-J
8-J
3
Center Bar
313
GM-413
613
813
4
Guide Bar (2 requi
red)
314
414
614
814
5
Handle
GM-3415
GM-3415
6815
6815
5
Handle
TS-3415*
TS-3415*
--
--
6
Locking Ring
SV-3416
(1/2” Hole
)
GM-416
(
5
/8” Hole)
SV-6816
(3/4” Hole)
SV-6816
(3/4” Hole)
7
Holding Ring
PA-3416*
*
GMPA-416**
PA-6816**
PA-6816**
8
Spring, Lock
GM-417
GM-417
6817
6817
9
Spring, Holding
PA-3417**
GMPA-417**
PA-6817**
PA-6817**
10
Crank
GM-3418
GM-3418
GM-6818
GM-6818
10
Crank
TS-3418*
TS-3418
*
--
--
10
Crank, with 1/8” Rollpin
GMPA-3418**
GMPA-3418*
*
GMPA-6818**
GMPA-6818**
11
Jaw Inserts, regular (set of 2)
319
419
619
819
11
Jaw Inserts, Hardened (set of 2)
319H
419H
619H
819H
12
Knob, Black -- 1" Dia., 1/4-20 thread
SV-3421(*)
--
--
--
12
Knob, Red -- 1" Dia., 1/4-20 thread
RSV-3421**
--
--
--
12
Knob, Black -- 1 1/2" Dia, 3/8-24 thread
--
SV-6821(*)
SV-6821
SV-6821
12
Knob, Red -- 1 1/2" Dia., 3/8-24 thread
--
RSV-6821**
RSV-6821**
RSV-6821**
13
Knob, Black -- 1 1/8" x 1 7/16" oval,
3/8-16 thread
OA-3421
OA-3421
--
--
13
Knob, Black -- 1" Dia., 1/4-20 thread
SV-3421*
SV-3421*
--
--
13
Knob, Red -- 1 1/8" x 1 7/16" oval,
3/8-16 thread
ROA-3421**
ROA-3421**
--
--
13
Knob, Black -- 1 1/2" Dia., 3/8-24 thread
--
--
SV-6821
SV-6821
13
Knob, Red -- 1 1/2" Dia., 3/8-24 thread
--
--
RSV-6821**
RSV-6821**
14
Stud
3423
6823
6823
6823
15
Screw -- 10-32 x 1/4 (2 required)
27
27
27
27
16
Screw -- 1/4-20 x 5/8
(2) 30-5/8
--
--
--
16
Screw -- 1/4-20 x 3/4
(2) 30-3/4
(6) 30-3/4
(6) 30-3/4
(6) 30-3/4
17
Adjusting Screw
SV-31
SV-31
SV-31
SV-31
18
Adjusting Screw – Female
PA-32**
PA-32**
PA-32**
PA-32**
19
Adjusting Screw – Male
PA-33**
PA-33**
PA-33**
PA-33*
*
20
Cover Plate
3437
3437
6837
6837
21
Shoulder Screw
39
39
39
39
Note 1.
Price not shown, as replacement body castings are not available. View shown is 4-GM with side extension. Models 3-SV, 6-SV and 8-SV do not have
side extensions. 3-TS and 4-TS have both sides ground at right angles to jaw inserts.
WHEN ORDERING PARTS, INDICATE PART NUMBER, MODEL NUMBER AND PRICE.
(Cont. from prev. page) pressure before replacing locking
plate. To assemble
Pumping Action "PA" Locking
Mechanisms,
the following steps must be carefully followed:
1.
Insert crank (10), keeping handle lever (5) in vertical position
during entire assembly.
2.
Insert rear portion of adjusting screw (18), screwing same in
as far as it will go.
3.
Place the holding ring (7) behind crank so that the pin
extending from the crank fits into the slot of the holding ring.
4.
Insert center bar (3) through the holding ring far enough so
that the holding spring (9) can be slipped on.
5.
Insert front portion of the adjusting screw (19) as far as it will
go.
6.
Insert locking ring (6) and push center bar through same.
7.
Insert locking spring (8), locating same correctly in relation
to the center hole.
8.
Adjust both adjusting screws until the rear portion (18)
makes contact with the holding ring and the front portion (19)
makes contact with the locking ring.
9.
Push center bar through entire unit.
10.
Turn adjusting screw front portion (19) a 3/4 turn clockwise,
and adjust rear portion (18) until the bar moves freely – making
sure that the handle lever is in vertical position against stop.
11.
Adjust forward portion of adjusting screw (19) until desired
pressure is obtained.
