background image

6.0 Operation

1.0 Use – 2.0 Safety information

9

2

Thank you for choosing HEATSTRIP™, the black light infrared electric heater. This 
user manual will guide you through the connection and programming of the radio 
receiver MHS-FBM. These instructions are an addition and valid only in combina-
tion with the general HEATSTRIP™ manual, chapter 4.7.

Our remote controls are powered by the EnOcean technology, which enables them 
to run battery free. When pressing the button of the remote control, the system 
harnesses the physical pressure of your thumb onto the remote control and 
converts it into an electro-magnetic signal that is picked up by our MHS-FBM 
receiver. 

Electronic smog and radio signals

Many people are worried about the possible consequences for their health of the 
electronic smog created by the countless electrical fields due to the many wireless 
devices we are surrounded by. Manufacturers hence worry about possible claims 
for damages based on such health related harm. Nevertheless, the need for 
wireless devices keeps increasing quickly. Therefore, we had the standard 
intensity of the electro-magnetic fields created by our radio receivers measured by 
ECOLOG under in situ usage conditions (ECOLOG is the German Institute for 
Socio-Ecological Research and Education).

What are the results?

1. The Enocean Radio system emits one hundred times less intensive 
high-frequency fields than conventional light switches (the latter’s high-frequency 
fields are produced through the characteristic sparkling switching process).
2. The intensity of the quick high-frequency emissions of the EnOcean radio switch 
are up to 10,000 times fewer than the permanent high-frequency emissions of the 
mobile phone network stations in residential homes.
3. Thanks to the lack of cables and switches, our radio system works without 
interefering with low-frequency electro-magnetic emissions.
4. This radio system is used in schools, hospitals, and even in houses built 
according to Feng Shui principles.

Standby operation:   heating off 
 

blue LED lit

ON  

press the ON button

 

heat output is set up on "power 3" (full power")

 

press the ON button again

 

Remote to “Power 0” (OFF)

Heat output  

press the OFF button

settings 

remote to “Power 2”

 

2 green LEDs turn on

 

press in OFF button again

 

remote to “Power 1”

 

1 green LED turns on

 

press in OFF button again

 

remote to “Power 0” (OFF)

 

All 3 green LEDs turn on

 

Standby operation, heating off – blue LED lit

Party mode 

The “Party Mode” has a preset heating duration of 4 hours 

 

running on maximum heat supply, regardless of the Time-Code 

 

set (see section “Setting of maximum heating duration” above).

To launch the  

Press and hold the ON button for more than 6 seconds. The heater  

“Party Mode”: 

is set on maximum heat and will switch off automatically after 4  

 

hours. The green and blue LEDs are lit.

General OFF 

Press and hold the OFF button for more than 6 seconds. The    

 

heater turns off regardless of the current heating setting. The blue  

 

LED displays the standby mode.

 
Test operation  

(to check the functionality of the receiver module without using the 

without transmitter  

transmitter)

 

Press the lateral button on the receiver for more than 10 seconds 

 

-> the heater turns on, 2 LEDs are lit, 80% power.

 

Press the programing buttons again for for more than 10 seconds,

 

the heater turns off.

 

If not, the device is automatically turned off after 2 hours. The blue  

 

standby LED turns on.

Содержание MHS-ESM













Отзывы: