(c)
wall mounting
bracket
(a)
mounting
strap
phillips head
screwdriver
flat head
screwdriver
(b)
screw M4x10
(d)
locater pin
rotated quarter
turn to lock
Fig. 2
Wall bracket Fixing Dimensions
Procedure for fixing Wall Brackets
Step 1
Using Dim. X and Dim. Y as a guide, mark the hole positions for the
four fixing brackets and drill and plug the wall to suit.
Note: Allow enough room above and below for the clearance stated.
Screw the four fixing brackets securely to the wall - see Fig. 3.
Step 2
Place carefully around the upright bars the 4 mounting straps at the
position shown - see Fig. 3. (Note the straps must be positioned up
tight to the cross bar as indicated) Securely fix them by screwing in
place fully the M4 x 10mm screw. Ensure the brackets are fitted with
the rear of the straps facing directly backwards.
Step 3
Place the towel rail straps into the wall mounted brackets, secure
them with the locater pins by inserting it and giving it a quarter turn
- see Fig 3. Check the four brackets and towel rail are fitting
horizontal. If not go back to step 2. The straps can be repositioned to
ensure that the towel rail is horizontal when fitted to your wall. If the
towel rail cross rails are not level, loosen both straps on either left or
right hand upright bar. Lower the two straps and raise up the towel
rail until it is horizontal, then secure as indicated in step 2 and 3.
Model(s)
Dim. X
Dim. Y
HSTR90C
505
165
HSTR120W
505
165
HSTR130C
505
230
HSTR175W
505
230
Cleaning
The finish on your towel rail can be maintained by occasionally wiping
over with a damp cloth and lightly finishing with a soft dry cloth. This
should only be carried out when the rail is cold.
Do
not
use abrasive
cleaning powders as this could damage the surface finish.
Recycling
For electrical products sold within the European Community.
At the end of the electrical products useful life it should not
be disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority or
retailer for recycling advice in your country.
After Sales Service
Your product is gauranteed for two years from the date of purchase.
Within this period, we undertake to repair or exchange this product
free of charge (excluding lamps & subject to availability) provided it
has been installed and operated inaccordance with these instructions.
Your rights under this gaurantee are additional to your statutory
rights, which in turn are not affected by this gaurantee.
Should you require after sales service, please get in touch with the
supplier through whom you purchased the appliance. It would assist
us if you can quote the model number, series, date of purchase and
nature of the fault at the time of your call. Please do not return a faulty
product to us in the first instance as this may result in loss or damage
and delay in providing you with a satisfactory service.
Please retain your receipt as proof of purchase.
Heatstore
Victoria Road,
Avonmouth
BS11 9DB
Tel: (0117) 923 5375 Fax: 0117 923 5374
IPX4
Fig. 3
mounting
strap
mounting
bracket
cross
bar
Note: Mounting strap
must be positioned up
tight to the cross bar
mounting strap
upright
bar
Detail view of
mounting
strap/cross
bar
Installation
The towel rail must be permanently fitted to the wall.
All models are supplied with wall brackets. The towel rail must be
mounted so that the top rail is horizontal and at least 50mm below
any overhanging surface - see Fig. 1.
Wall mounting
The Wall mounting accessory pack contains:
(a)
4 mounting straps
(b)
4 screws (M4 x 10)
(c)
4 wall mounting brackets
(d)
4 locator pins
The product complies with the European Safety Standards EN60335-2-46 and the European Standard Electromagnetic Compatibility (EMC) EN55014,
EN60555-2 and EN60555-3 These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
