manualshive.com logo in svg

Heatilator NNXT3933IF, Руководство по установке, Страница: 37 / 58

Поделиться
Скачать
Heatilator NNXT3933IF Скачать руководство пользователя страница 37

37

Heatilator  •  NNXT4236IF, NNXT4236ILF, NNXT3633IF, NNXT3633ILF Installation Manual  •  4055-980  Rev. D  •  9/15 

A. General Information

WARNING! Risk of Shock or Explosion! DO NOT

 wire 

110-120 VAC to the valve or to the appliance wall switch. 
Incorrect wiring will damage controls.

NOTICE: 

This appliance must be electrically wired 

and grounded in accordance with local codes or, in the 
absence of local codes, with 

National Electric Code 

ANSI/NFPA 70-latest edition

 or the 

Canadian Electric 

Code CSA C22.1.

•  Wire the appliance junction box to unswitched 110-

120 VAC. This is required for proper operation of the 
appliance (Intelli

fi

 re ignition).

•  A 110-120 VAC circuit for this product must be protected 

with ground-fault circuit-interrupter protection, in 
compliance with the applicable electrical codes, when 
it is installed in locations such as in bathrooms or near 
sinks.

•  Low voltage and 110-120 VAC voltage cannot be shared 

within the same wall box.

Accessories Requirements

•  This appliance may be used with a wall switch, wall 

mounted thermostat and/or a remote control.

Wiring for optional Hearth & Home Technologies approved 
accessories should be done now to avoid reconstruction. 
Follow instructions that come with those accessories.

8 

8 

Electrical Information 

WHT

WHT

BLK

BLK

GRN wire 
inside box

Copper
ground attached
to GRN screw with
GRN wire

14/2WG

Cover Plate
outside firebox

Romex 
Connector

Figure 8.1 Junction Box Detail

NOTICE: DO NOT

 wire 

110-120 VAC to wall switch.

Junction Box Installation

If the box is being wired from the 

INSIDE

 of the appliance:

•  Remove the screw attaching the junction box/receptacle 

to the outer shell, rotate the junction box inward to dis-
engage it from the outer shell (see Figure 8.1).

•  Pull the electrical wires from outside the appliance through 

the opening into the valve compartment and secure wires 
with a Romex connector. See Figure 8.1.

•  Make all necessary wire connections to the  junction box/

receptacle and reattach the junction box/receptacle to 
the outer shell.

Electrical Service and Repair

WARNING! Risk of Shock! 

Label all wires prior to dis-

connection when servicing controls. Wiring errors could 
cause improper and dangerous operation. Verify proper 
operation after servicing.

WARNING! Risk of Shock! 

Replace damaged wire with 

type 105º C rated wire. Wire must have high temperature 
insulation.

IntelliFire™ Plus Ignition System Wiring

NOTICE: 

Batteries should only be used as a power source 

in the event of an emergency power outage. Batteries 
should not be used as a primary long-term power source. 
Battery polarity must be correct when installing batteries. 

Do not store batteries in the battery pack when the 
appliance is powered by the 6 volt transformer connected 
to permanent electrical service.

•  Wire the appliance junction box to 110-120 VAC for 

proper operation of the appliance.

WARNING! Risk of Shock or Explosion! DO NOT

 wire 

IPI controlled appliance junction box to a switched circuit. 
Incorrect wiring will override IPI safety lockout.

•  Refer to Figure 8.2, IPI Wiring Diagram.
•  This appliance is equipped with an IntelliFire Plus™

 

control valve which operates on a 6 volt/1.5 AMP system.

•  Plug the 6 volt transformer plug into the appliance junction 

box to supply power to the unit OR install 4 AA  cell 
batteries (not included) into the battery pack before use.

B. Wiring Requirements

Содержание NNXT3933IF



























































Отзывы:

Нет отзывов