Heatilator NB3630 Скачать руководство пользователя страница 26

Страница: 26 / 64

Heatilator • Novus BV • 4031-551 Rev B • 12/06

Latches

(both bottom

and top)

Glass

Assembly

Figure 12.2 Glass Assembly

Handle glass with care.
• Inspect the gasket to ensure it is

undamaged.

• Inspect the glass for cracks, chips or

scratches.

• Do NOT strike, slam or scratch glass.
• Do NOT operate appliance with glass

assembly removed, cracked, broken or
scratched.

• Replace glass assembly as a complete

assembly.

WARNING

I. Hood

The hood is to be located above the glass panel. The hood
must be attached or a

re hazard may result. Locate the four

screws just inside the upper section of the appliance. Posi-
tion the hood and slide into position. Tighten the four screws.
See Figure 12.3.

Figure 12.3 Installing the Hood

H. Grilles and Trim

• Install optional marble and brass trim surround kits using

the installation instructions included with them.

• Marble, brass, brick, tile or other non-combustible

materials can be used to cover the gap between sheet
rock and appliance.

• Do not obstruct or modify the air inlet/outlet grilles.
• Leave space to lower the bottom grille and remove the

trim door.

G. Glass Assembly

Removing Glass Assembly

• Remove

rescreen.

• Pull the four (30/33/36 in. appliances) or seven (42 in.

appliance) glass assembly latches out of the groove on
the glass frame.

• Remove the glass panel from the appliance.

Replacing Glass Assembly

• Set the glass panel on the lower two or four glass assembly

latches, ensuring the glass panel is centered in the
opening.

• Pull out and latch all four or seven glass assembly latches

into the groove on the glass frame.

• Replace

rescreen.

Содержание NB3630

































































Результаты поиска

Содержание NB3630

Отзывы:

Heatilator NB3630, Руководство пользователя, Страница: 26 / 64

Результаты поиска

Содержание NB3630

Отзывы: