manualshive.com logo in svg

Heat-N-Glo BE-41, Руководство по установке, Страница: 28 / 29

Поделиться
Скачать
Heat-N-Glo BE-41 Скачать руководство пользователя страница 28

30

Step 11.  Before Lighting  the Fireplace

Before

 lighting the fireplace, be sure to do the following:

Remove all paperwork from underneath the fireplace.
Review safety warnings and cautions

• Read the 

Safety and Warning Information

 section at

the beginning of this 

Installers Guide

.

Double-check for gas leaks

• Before lighting the fireplace, double-check the unit for

possible gas leaks.

Double-check vent terminations and front grilles for

obstructions.

• Before lighting the fireplace, double-check the unit for

possible obstructions that could be blocking the vent ter-

minations or the front grilles.

Double-check for faulty components

• Any component that is found to be faulty 

MUST BE

 re-

placed with an approved component. ampering with the

fireplace components is 

DANGEROUS

 and voids all war-

ranties.

A small amount of air will be in the gas supply lines. When

first lighting the fireplace, it will take a few minutes for the

lines to purge themselves of this air. Once the purging is

complete, the fireplace will light and will operate normally.
Subsequent lightings of the fireplace will not require this

purging of air from the gas supply lines,

 unless

 

the gas

valve has been turned to the OFF position

, in which

case the air would have to be purged.

NOTE:

 The fireplace should be run for 8 hours on the initial

start-up. This will help to cure the chemicals used in the

paint and logs.

Step 12.   Lighting the Fireplace

You’ve reviewed all safety warnings, you’ve checked the

fireplace  for  gas  leaks,  you  know  the  vent  system  is

unobstructed, and you’ve checked for faulty components.

Now you’re ready to light the fireplace.

WARNING: PLEASE REFER TO THE USER’S

MANUAL FOR ALL CAUTIONS, SAFETY,  AND

WARNING  INFORMATION  PERTAINING  TO  THE

LIGHTING AND OPERATION OF THE FIREPLACE.

After the Installation

LEAVE THIS INSTALLATION MANUAL WITH

THE APPLIANCE FOR FUTURE REFERENCE.

!

!

Placing the Ember Material

Ember material is shipped with this gas fireplace. The bag

labeled Glowing Ember (050-721) is standard glowing ember

material. To place the ember material:

• Pull the four glass latches out of the groove on the glass

frame. Remove glass door from the unit (see Figure 39).

• Place dime size pieces of Glowing Ember (050-721)

ember material about 1/2 inch apart near port holes in

burner top. Do NOT press embers into burner ports. Cover

the top of the burner with a single layer of ember mate-

rial. For best performance do NOT place embers on the

ports at the rear of the burner.

• Save the remaining ember materials for use during fire-

place servicing.

• Replace the glass door and a front trim door on the unit.

• Pull out and latch the glass clips into the groove on the

glass frame.

Glass Specifications:

BE-41:      24 1/2  X  35 1/2    TEMPERED

CAUTION:  IT  IS  STRONGLY  RECOMMENDED  THAT

TRIM DOORS WITH OPTIONAL MESH SCREENS BE IN-

STALLED ON PROPANE MODELS.

Figure 40.   Placement of the Ember Material

Figure 39.  Glass Assembly

Содержание BE-41






























Отзывы:

Нет отзывов