background image

Heat & Glo  •  MEZZO1000-AUB, MEZZO1300-AUB, MEZZO1300ST-AUB, MEZZO1600-AUB Owner’s Manual  •  2304-974 Rev. C  •  3/16  

12

F.  Lighting Instructions (IPI)

FOR YOUR SAFETY READ BEFORE LIGHTING

TO TURN OFF GAS TO APPLIANCE

1. This appliance is equipped with an ignition device which

automatically lights the burner. DO NOT try to light the burner by hand.

1.  Equipped with wall switch: Turn ON/OFF switch to OFF.

 

Equipped with remote or wall control:  Press OFF button.

 

Equipped with thermostat:  Set temperature to lowest setting.

WARNING: If you do not follow these instructions exactly, a fi re or explosion may result causing property damage, personal injury or loss of life.

WARNING:

NOT FOR USE WITH SOLID FUEL

GAS

VALVE

For additional information on operating your

 Hearth & Home Technologies fi replace, please refer to www.fi replaces.com.

A.  This appliance is equipped with an intermittent pilot ignition (IPI) device which 

automatically lights the burner. DO NOT try to light the burner by hand.

B. BEFORE LIGHTING, smell all around the appliance area for gas.  Be sure to smell 

next to the fl oor because some gas is heavier than air and will settle on the fl oor.

WHAT TO DO IF  YOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; do not use any phone in your building.

DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240 VAC) TO THE CON-

TROL VALVE.
Improper installation, adjustment, alteration, service or maintenance can cause 

injury or property damage. Refer to the owner’s information manual provided with 

this appliance. For assistance or additional information, consult a qualifi ed installer, 

service agency or the gas supplier.
This appliance needs fresh air for safe operation and must be installed so there are 

provisions for adequate combustion and ventilation air.
If not installed, operated, and maintained in accordance with the manufacturer’s in-

structions, this product could expose you to substances in fuel or fuel combustion which 

are known to the State of California to cause cancer, birth defects, or other reproductive 

harm.
Keep burner and control compartment clean. See installation and operating instruc-

tions accompanying appliance.

Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline 

and other liquids having fl ammable vapors away.
DO NOT operate the appliance with fi xed glass assembly removed, cracked or 

broken. Replacement of the fi xed glass assembly should be done by a licensed or 

qualifi ed service person.

•   Immediately call your gas supplier from a neighbor’s phone. Follow the gas sup-

plier’s instructions.

•    If you cannot reach your gas supplier, call the fi re department.
C.  Use only your hand to push in or turn the gas control knob.  Never use tools.  If 

the knob will not push in or turn by hand, DO NOT try to repair it, call a qualifi ed 

service technician.  Force or attempted repair may result in a fi re or explosion.

D. DO NOT use this appliance if any part has been under water. Immediately call 

a qualifi ed service technician to inspect the appliance and to replace any part of 

the control system and any gas control which has been under water.

For use with natural gas and propane. A conversion kit, as supplied by the manufac-

turer, shall be used to convert this appliance to the alternate fuel.
Also Certifi ed for Installation in a Bedroom or a Bedsitting Room.
This appliance must be installed in accordance with local codes, if any; if none,  

follow the 

National Fuel Gas Code, ANSIZ223.1/ NFPA 54, or the National Gas and 

Propane Installation code, CSA B149.1.

LIGHTING INSTRUCTIONS (IPI)

2. Wait 

fi ve (5) minutes to clear out any gas. Then smell for gas, including near the 

fl oor. If you smell gas, STOP! Follow “B” in the Safety Information located on the 

top of this label. If you do not smell gas, go to next step.

3.  To light the burner:    

 

Equipped with wall switch: Turn ON/OFF switch to ON.

  Equipped with remote or wall control:  Press ON or FLAME button.

Equipped with thermostat: Set temperature to desired setting.                                                   

4.  If the appliance does not light after three tries, call your service technician or gas 

supplier.

2.  Service technician should turn off electric power to the control when performing 

service.

DANGER

HOT GLASS 

WILL CAUSE BURNS.

DO NOT TOUCH 

GLASS UNTIL COOLED.

NEVER

ALLOW CHILDREN TO TOUCH GLASS.

CAUTION:

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this 

appliance and shall be installed for the protection of children and other at-risk individuals.

593-913i

Содержание MEZZO1000-AUB




































Отзывы: