Heat & Glo • TIARAP-BK-IPI, TIARAP-BR-IPI, TIARAP-CES-IPI Owner’s Manual • 2344-981 • 5/14
12
Figure 3.4 Control Module
Control Module Operation
1. The control module has an ON/OFF/REMOTE selector
switch that must be set. See Figure 3.4.
OFF Position: Appliance will ignore all power inputs and
will not respond to any commands from a wall switch or
remote. The unit should be in the OFF position during
installation, service, battery installation, fuel conversion,
and in the event that the control goes into LOCK-OUT
mode as a result of an error code.
ON Position: Appliance will ignite and run continuously
in the HI
fl
ame setting, with no adjustment in
fl
ame
output. This mode of operation is primarily used for
initial installation or power outage operation with battery
backup.
REMOTE Position: Appliance will initiate commands
from an optional wired wall switch and/or the wireless
remote (RC100, RC200, RC300).
2. If using the wired switch in the control cavity with the
module in REMOTE mode, the
fl
ame output can be
adjusted with the HI/LO selector switch on the module.
See Figure 3.6. Note that the
fl
ame HI/LO selector
switch will become inactive once an optional remote
control (RC200/RC300) is programmed to the control
module. Note that the control module will always ignite
the
fi
replace on HI and remain so for the initial 10
seconds of operation. If the HI/LO is switched to the
LO position, the
fl
ame output will automatically drop to
the lowest setting after the
fl
ame has been established
for 10 sec. After this 10 second period, the
fl
ame can
be adjusted from HI to LO with the switch.
3. The control module has safety feature that automatically
shuts down the
fi
replace after 9 hours of continuous
operation without receiving a command from the RC300
remote.
4. If you intend to use both the wired appliance switch and
the RC300 remote control to operate your
fi
replace, the
appliance switch will override any commands given
by the remote.
5.
Module Reset
This module may lock-out under certain conditions.
When this occurs, the appliance will not ignite or
respond to commands. The module will go into
lock-out mode by emitting three audible beeps, then
continuously displaying a RED/GREEN error code at
its status indicator LED.
• Check battery tray. Remove batteries if installed.
Batteries should only be installed for use during power
outages. See Section H.
• Locate the module selector switch. (See Figure 3.6).
• Set the module selector switch to the OFF position.
• Wait
fi
ve (5) minutes to allow possible accumulated
gas to clear.
• Set the module selector switch to ON or REMOTE
position.
• Start the appliance.
WARNING! Risk of Explosion! DO NOT
press the mod-
ule reset switch more than one time within a
fi
ve minute
time period. Gas may accumulate in
fi
rebox. Call a quali-
fi
ed service technician.
Nine Hour Safety Shutdown Feature
The appliance has a safety feature that automatically
shuts down the
fi
replace after nine hours of continuous
operation without receiving a command from the wall
switch or optional remote.
I. Detailed Component Operating Instruc-
tions - IntelliFire Plus
LP/NG GAS-TYPE
SELECTOR SWITCH
WIRE LEAD FROM
REGULATOR CONNECTS HERE
MODULE
Optional Fan Operation
If desired, a fan kit may be added. Contact your dealer
to order the correct fan kit. Heat management for the fan
is discussed in Section 3.G. Detailed instructions are in-
cluded with the fan kit.
Appliance ON/OFF
If an optional remote control or wall control is installed,
it should be used to control the ON/OFF function of the
appliance. Follow instructions included with the installed
control.
To operate the appliance without a wall control or remote
control, use the ON/OFF switch located on the front panel
of the control cavity of the appliance. See Figure 3.5.
CAUTION! Risk of Electric Shock!
Avoid touching wires
and electrical components in appliance control cavity.
