12
Lighting Instructions
Checking For LP Gas Leaks
ignitor will click and spark to ignite burner. Ignitor may need
realignment to generate adequate spark.
8. Confirm ignition by viewing flame through the convection
plate holes.
9. If the burner does not light, turn the control knob to OFF,
wait 5 minutes for gas to clear, then retry.
10. Adjust control knob to the desired cooking temperature.
To light the gas grill by match, follow steps 1 through 6 of the
Basic Lighting Procedures. Then, insert a lit match through
the lighting hole on either side of the grill (see Figure 7). Turn
the nearest control knob to the HIGH setting to release gas.
The burner should light immediately.
1. Use a commercially-available non-corrosive leak check
solution.
2. Turn the grill control knob to the full OFF position, then
turn the gas ON at source.
3. Apply the leak check solution to all gas connections.
Bubbles will appear in the leak check solution if the
connections are not properly sealed. Tighten or repair
as necessary.
4. If there is a gas leak that cannot be repaired, turn
off the gas at the source, disconnect fuel line from
the grill and call the gas grill dealer, or gas supplier
for repair assistance.
Figure 7
Lighting the Grill by Match
MATCH LIGHT
THROUGH ONE
OF THESE
HOLES
Basic Lighting Procedures
1. Familiarize yourself with the safety guidelines at the front
of this manual. Do not smoke while lighting grill or
checking gas supply connections.
2. Be sure the LPG cylinder is filled.
3. Make sure all gas connections are securely tightened.
4. Ensure that 2 - "D" size batteries have been installed.
5. Open the grill lid.
6. Set control knob to OFF and open the LPG cylinder valve.
7. Push and turn ignitor control knob to HIGH. The built-in
Failure to open the grill lid during the lighting pro-
cedures could result in a fire or explosion which could
cause property damage, serious bodily injury or death.
Explosion Risk
Fire Risk
WARNING
IF YOU SMELL GAS:
Failure to comply with these instructions could result
in a fire or explosion which could cause property
damage, serious bodily injury or death.
Explosion Risk
Fire Risk
WARNING
•
Shut off gas supply to the grill.
•
Extinguish any open flame.
•
Open grill lid.
•
If odor continues, immediately call your gas
company or local fire department.
WARNING
Never
test for leaks with a flame. Check for gas leaks
prior to first use, at the beginning of each season, or
every time the LPG cylinder is changed. Follow these
four steps:
Hot Surfaces
•
Never
lean over the grill cooking area
while lighting the gas grill.
• Keep face and body a safe distance (at
least 18 inches) from the lighting hole or
burners, when lighting the grill by match.
Failure to comply with these instructions could result
in a fire or explosion which could cause property
damage, serious bodily injury or death.
Fire Risk
Explosion Risk
WARNING
A strong gas smell, or the hissing sound of gas indicates
a serious problem with the gas grill or the LPG cylinder.
•
Get away from the LPG cylinder.
•
Do not try to fix the problem yourself.
•
Call the fire department. (Do not call near the LPG
cylinder because the telephone is an electrical device).
Lighting Instructions
Checking For LP Gas Leaks
ignitor will click and spark to ignite burner. Ignitor may need
realignment to generate adequate spark.
8. Confirm ignition by viewing flame through the convection
plate holes.
9. If the burner does not light, turn the control knob to OFF,
wait 5 minutes for gas to clear, then retry.
10. Adjust control knob to the desired cooking temperature.
To light the gas grill by match, follow steps 1 through 6 of the
Basic Lighting Procedures. Then, insert a lit match through
the lighting hole on either side of the grill (see Figure 7). Turn
the nearest control knob to the HIGH setting to release gas.
The burner should light immediately.
1. Use a commercially-available non-corrosive leak check
solution.
2. Turn the grill control knob to the full OFF position, then
turn the gas ON at source.
3. Apply the leak check solution to all gas connections.
Bubbles will appear in the leak check solution if the
connections are not properly sealed. Tighten or repair
as necessary.
4. If there is a gas leak that cannot be repaired, turn
off the gas at the source, disconnect fuel line from
the grill and call the gas grill dealer, or gas supplier
for repair assistance.
Figure 7
