Heat & Glo MONTANA MONTANA-36 Скачать руководство пользователя страница 15

Страница: 15 / 44

Heat & Glo LifeStyles Collection • Montana US-CAN • 4039-156 Rev C • 11/07

A. Chimney Requirements

Vertical distances are measured from the base of the

re-

place.

To determine the chimney components needed to complete
your particular installation, follow the steps below:

• Determine the total vertical height of the fireplace

installation. This dimension is measured from the base of
the

replace assembly to the point where the smoke exits

the termination cap.

• Subtract the effective height of the

replace assembly from

the overall height of the

replace installation (measured

from the base of the fireplace to the bottom of the
termination cap).

• Refer to Table 5.1 to determine what components must

be selected to complete the

replace installation.

• Determine the number of ceiling

restops, stabilizers,

roof flashing, etc. required to complete the fireplace
installation.

Table 5.1

• Do NOT connect this fireplace to a chimney flue

servicing another appliance.

• Do NOT connect to any air distribution duct or

system.

CAUTION

Fire Risk

• Must maintain 2 in. (51 mm) air clearance

to insulation and other combustible
materials.

WARNING

Note:

A maximum of two pairs of offsets and returns may

be used.

Chimney Assembly

• Minimum overall straight height

4.27

• Minimum height with offset/return

4.88

• Maximum height

27.43

• Maximum chimney length between an offset

and return

6.1

• Maximum distance between chimney

stabilizers

10.67

• Double offset/return minimum height

7.32

• Maximum unsupported chimney length

between the offset and return

1.83

• Maximum unsupported chimney height above

the

replace

10.67

• Minimum overall straight height if

replace is

freestanding

6.33

1.93

HEIGHT OF CHIMNEY COMPONENTS

in.

Canada

Chimney Stabilizer

SL11

SL4

4-3/4

121

Ceiling Firestops

FS538

FS540

Offsets/Returns

SL1130

SL430

14-1/2

368

Roof Flashing

RF570

RF571

Chimney Sections*

SL1106

SL406

4-3/4

121

SL1112

SL412

10-3/4

273

SL1118

SL418

16-3/4

425

SL1136

SL436

34-3/4

883

SL1148

SL448

46-3/4

1187

n/a

SLA10

16-3/4

425

* Dimensions re

ect effective height.

Содержание MONTANA MONTANA-36













































Результаты поиска

Содержание MONTANA MONTANA-36

Отзывы:

Похожие инструкции для MONTANA MONTANA-36

Бренды по названию

Популярные бренды

Heat & Glo MONTANA MONTANA-36, Руководство пользователя

Результаты поиска

Содержание MONTANA MONTANA-36

Отзывы:

Похожие инструкции для MONTANA MONTANA-36

Бренды по названию

Популярные бренды